Go Back   Home > Forums > Amplifiers > Chip Amps

Chip Amps Amplifiers based on integrated circuits

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 7th December 2009, 01:38 PM   #131
0kk0 is offline 0kk0  Netherlands
diyAudio Member
 
Join Date: Sep 2009
try this site for calculating the resistor values from the colored rings...
Graphical Resistance Calculator
  Reply With Quote
Old 7th December 2009, 05:45 PM   #132
diyAudio Member
 
Join Date: Nov 2009
Quote:
Originally Posted by 0kk0 View Post
try this site for calculating the resistor values from the colored rings...
Graphical Resistance Calculator
The image is not from my system
My resistor has burned and i can't see the colors
I was hoping that someone that has this system tell me the resistor value or colors
But thanks for reply.
  Reply With Quote
Old 13th December 2009, 07:24 PM   #133
diyAudio Member
 
Join Date: Dec 2009
Default A bit of Help

Hello!

My name is Xavi, I'm from Spain and I don't speak English very well; I hope you have a little bit of patience for me .

I have a Logitech z5500 with PID = R544 (with NO RCA read the subwoffer; the speakers are connected by wires directly).

My control center (POD) isn't working, I looked into this and I have found a chip Cirrus Logic CS42526 "burned". My POD is always "Detecting..." on the display .

I have searched a LOT by the internet to How to connect my PC to the subwoffer without using any POD. I have read a little bit this topic, but it's difficult to me to assimiler all the things. And i looked that you have post the PIN wires for RCA subwoffer. They are different wired.

My request :

- Does anyone "transformes" a non-RCA subwoffer to a PODLess system?
- Can anyone explain me briefly the steps?
- Which material/s I will need for this?

I will be very grateful to the responses.

I hope you will forgive me for my bad writing... But I prefeer write my own English than a automatic traducer, sometimes they doesn't work well.


Thanks!!
  Reply With Quote
Old 14th December 2009, 01:31 PM   #134
diyAudio Member
 
Join Date: Dec 2009
I add a Picture taken by me of my opened POD:

Click the image to open in full size.

The names of colors are in Spanish; but I put the names of colors under every wire .

I put the voltage of every wire; the wires which doesn't have any voltage is because my tester doesn't give me any good result for this one.

I look that the people had connected satellites to an amplifier and then connect subwofer to the amplifier. I don't want that. I don't have any amplifier, only the z5500 system, and my amplifier will be the subwofer.

Thanks to all .
  Reply With Quote
Old 16th December 2009, 06:39 PM   #135
diyAudio Member
 
Join Date: Dec 2009
OK, I'm trying to do that; I have some problems:

In the tutorial by lakata, there are two wires with 100Ohm, PIN11 and PIN12. Ok, but my PIN11 has got 3v :S. I believe my DB15 is a little bit different..

I can't find PIN6 on the DB15. The wire has only 14 mini-wires into. My PIN6 is disappear. I can't turn ON the Amplifier.Or this is what I think... How can I know if my Amplifier is ON, if i d'ont connect any speakers.

Can anyone give me some help?

Thanks.
  Reply With Quote
Old 17th December 2009, 09:35 AM   #136
diyAudio Member
 
Join Date: Dec 2009
z5500 kontrol paneli modlama

z5500 pod mod.
  Reply With Quote
Old 18th December 2009, 10:55 AM   #137
diyAudio Member
 
Join Date: Nov 2009
pin 11 is gnd from 8v supply
you must have 8 v between pin 11 and 10
you must connect a speaker and touch the wires from the input
if you hear something in speaker when you touch amps are ON
  Reply With Quote
Old 18th December 2009, 12:54 PM   #138
diyAudio Member
 
Join Date: Dec 2009
Yes, OK Adrian Vista.

I touch the inputs and only sounds the central speaker :S. Other speakers doesn't sound when I touch the wire . The enable wires are connected to GND and I have test to conect to 8v too; but other speakers doesn't sound...

I think that I will open my subwoffer to see if any is broken .


Thanks!
  Reply With Quote
Old 18th December 2009, 03:10 PM   #139
diyAudio Member
 
Join Date: Nov 2009
what pins you connected to GND?
  Reply With Quote
Old 18th December 2009, 11:37 PM   #140
diyAudio Member
 
Join Date: Dec 2009
PIN7 and PIN8 to GND.

If I conect PIN7 to "1", speakers are mutted. This PIN is for mutting speakers if it is enabled, but other one?

Thanks for your help
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
(Hacking the) Logitech Z-5300 pinouts? superxpro12 Chip Amps 2 23rd October 2009 03:02 AM
a big z5500 problem sonofwind Chip Amps 0 12th March 2009 02:07 AM
Z5500 from Home to Truck! fireplug0510 Car Audio 1 3rd February 2008 09:00 PM
Logitech z5500 sattelites TB W3-871s. willhub Full Range 21 18th December 2006 07:50 PM


New To Site? Need Help?

All times are GMT. The time now is 05:27 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2