Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

TDA7293 Max PO without high-n circuit?
TDA7293 Max PO without high-n circuit?
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 16th September 2005, 07:46 AM   #1
Bosium is offline Bosium  South Africa
diyAudio Member
Bosium's Avatar
Join Date: Oct 2002
Location: Essex, UK
Question TDA7293 Max PO without high-n circuit?

Hi All

Just a quick question to anyone who has used TDA7293s before. I'm hoping to squeeze 75Wrms out of mine, is it possible without exceeding the dissipation ratings of the Multiwatt 15 package?

In the datasheet it implies that without the high-efficiency circuit power is more or less max at 50Wrms per device but I was hoping someone here might have some personal experience to share..

If this is the case, I will trim down the rail voltages so that they limit output power to 50 or 60w per device.

Thanks a ton

  Reply With Quote
Old 16th September 2005, 12:46 PM   #2
Eva is offline Eva  Spain
diyAudio Member
Eva's Avatar
Join Date: Oct 2003
Location: Near the sea
Send a message via MSN to Eva
I have not any experience with the new TDA7293, but I've used the older TDA7294 with +-40V regulated rails and gentle forced cooling (without high efficiency circuit) to produce in excess of 150W on a 4 ohm load (not continuously). Note that some speaker loads may trigger overcurrent protection, so reducing rails to +-35V is recommended. Anyway, 100W at 4 ohms are quite easy to achieve with that IC.

Note that the heatsink I was using measured almost 10cm height by 8cm width by 4cm depth and had a 8cm fan just in front of it, and that the IC was directly bolted to the heatsink with only a thin layer of thermal compound inbetween, since insulators would increase thermal resistance too much.
  Reply With Quote
Old 19th September 2005, 10:39 AM   #3
Bosium is offline Bosium  South Africa
diyAudio Member
Bosium's Avatar
Join Date: Oct 2002
Location: Essex, UK
Hi Eva

I will be using the TDA7293s on a large heatsink extrusion, passively cooled. I will have to use isolation, but I will use Mica if possible, that rubber doesnt work too well.

I was under the impression that 80W was really pushing it from these ICs, but you say 100W is easily attainable?

I'm talking continuous RMS power, I will be happy if I can squeeze 75W out of each as my topology is dual channel, 2-chips per channel in parallel modular arrangement. That would give me 150W into 2 ohm or bridged into 300W into 4 ohm - plenty plenty plenty.

  Reply With Quote


TDA7293 Max PO without high-n circuit?Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
TDA7293 - Need help on circuit Fossil Chip Amps 8 23rd July 2017 12:09 AM
High input impedance X circuit zelter Pass Labs 4 31st March 2009 10:06 PM
AlephX High Power version circuit needed space2000 Pass Labs 3 13th June 2008 12:50 AM
tda7293 circuit Al Bundy Chip Amps 4 4th July 2004 11:10 AM
Need help designing high-gain amp circuit! electec Chip Amps 2 13th November 2003 01:01 AM

New To Site? Need Help?

All times are GMT. The time now is 11:31 AM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio