My JL 4 channel amp is not recieving power. - diyAudio
Go Back   Home > Forums > General Interest > Car Audio

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 21st January 2014, 01:34 AM   #1
diyAudio Member
 
Join Date: Jan 2014
Default My JL 4 channel amp is not recieving power.

First of all, I would like to clarify that I have followed all of the basic and most advanced steps to trying to resolve my problem. When we first had everything set up, only my left highs and mids were working. We tested all the power and everything was correct. Twenty minutes later we turned the car back on and all my speakers were working. Now, my amp won't turn on at all. I am assuming it's the amp but just in case I figured I would post up here.

Please excuse the large picture but I want you to see everything.

Click the image to open in full size.
  Reply With Quote
Old 21st January 2014, 01:07 PM   #2
diyAudio Member
 
evianamp2011's Avatar
 
Join Date: Nov 2010
Location: Texas
If your amplifier is not turning on you have to make sure you have B+ (12.6v) on your terminals and that your ground is good. As well as voltage on the remote, if any of those are missing well the amplifier will not turn on.

Check the fuse by the battery and by the amp if you have one near it, they might have popped when all 4ch were working and you may have gotten a bit happy and cut up the volume enough to pop fuses (if the fuses where low amperage rating).


Sounds like bad RCA's if you ask me, but I would check all the speaker wires to make sure none of them are pinched and shorted same with the RCA. RCA sometimes have crappy solder connections inside the ends, if possible untwist one open and check out the connections (two connections, the middle pin and the outer jacket). If they are loose then you might get sound sometimes but most of the time is going to be intermitting or off.


What amplifier is pushing the sub?....not a good idea to mount your amp to your subwoofer enclosure (unless its well braced inside) and even then not a good idea.
__________________
Tek 465, Fluke 111, TPI 440, AudioAuthority 2/77 Power Supply, Alpine HU for signal or Eico 379 Sine/Square Wave Generator.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
JL Audio AMP MHD750.1 Turns on! Power goes from GREEN TO RED superjoey01 Class D 4 11th July 2012 08:12 PM
JL 13W7AE car subwoofer in JL Gotham 213 Vs B&W ASW 855 muddasirwaheedmalik Subwoofers 9 9th September 2011 05:34 AM
JL 300 sub 2 channel amp...and a stinky smell aptquark Car Audio 2 25th September 2010 09:54 PM
1 JL 12w0 on a 500/1 amp lol never too much power right? TeeJay850 Subwoofers 5 18th June 2008 12:54 PM


New To Site? Need Help?

All times are GMT. The time now is 07:06 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2