directed 600D schematic or resistor value please? - diyAudio
Go Back   Home > Forums > General Interest > Car Audio

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 17th November 2012, 01:46 AM   #1
diyAudio Member
 
Join Date: Apr 2011
Location: Anchorage AK
Red face directed 600D schematic or resistor value please?

the first series of this amp(99-01/2) board rev.A, mfg 03/2000. anyways r51 and r52 are toast. they should be the same. also, would be nice to know the part number for d51, and d53. on a side note, would be curious if anyone knows what goes in u108/u109, as they are ground at the factory, but i think they are fine....... thanks,
-Heath H-
  Reply With Quote
Old 17th November 2012, 02:11 PM   #2
diyAudio Member
 
Join Date: Nov 2003
Location: Louisiana
If no one can help. post a photo of the board.
  Reply With Quote
Old 20th November 2012, 10:35 AM   #3
diyAudio Member
 
Join Date: Apr 2011
Location: Anchorage AK
here's the board. just figured out how to upload pics quicker. need better pics?
Click the image to open in full size.
  Reply With Quote
Old 20th November 2012, 11:08 AM   #4
diyAudio Member
 
Join Date: Nov 2003
Location: Louisiana
Since I don't have anything specifically for this amp, I would need a relatively good photo of the area were the resistors are located.
  Reply With Quote
Old 20th November 2012, 02:26 PM   #5
diyAudio Member
 
Join Date: Apr 2011
Location: Anchorage AK
best i can do right now. a couple of the pics didn't upload for some reason..... oh, there they went. moved the original, so i think i'll upload that one, too.
Click the image to open in full size.Click the image to open in full size.Click the image to open in full size.Click the image to open in full size.Click the image to open in full size.Click the image to open in full size.
  Reply With Quote
Old 20th November 2012, 02:30 PM   #6
diyAudio Member
 
Join Date: Apr 2011
Location: Anchorage AK
hmm, can't seem to make it upload in high res. should be at 2592*1944... i may see if i can find the time to pop open the 750d, and 1100d and try to match up the circuit. thanks.
  Reply With Quote
Old 20th November 2012, 03:08 PM   #7
diyAudio Member
 
Join Date: Nov 2003
Location: Louisiana
It looks like the Memphis circuit. The resistors are 22 ohms.

The 16 pin IC is an MC14060. The 14 pin IC is an LM361.

The service manual for the JBL BP1200.1 has schematic diagrams that are very close to many parts of this amp.
  Reply With Quote
Old 21st November 2012, 06:27 AM   #8
fra is offline fra  Slovenia
diyAudio Member
 
Join Date: Jul 2010
here is service manual for jbl bp 1200.1
JBL BP1200.1 SM Service Manual free download, schematics, eeprom, repair info for electronics
  Reply With Quote
Old 21st November 2012, 12:29 PM   #9
diyAudio Member
 
Join Date: Apr 2011
Location: Anchorage AK
thank you guys. so, i'm assuming this is the rectifier circuit for the ic/etc regulators, as it shows in the bp1200 schematic. if that is the case, i am going on the assumption that these both had to have failed at the same time for whatever reason, i.e. freeze, and shorted. it's just weird that both sides of the circuit have the heat damage equally, from running the higher current, but only the one cap seems definitely blown. i just don't want to miss something else that could have caused this.

i am just ordering parts at this point, but i will be replacing the 2 caps, 2 resistors, and the 4 diodes, even though just the 2 got hot. will also be replacing the rail caps, which i already have. did i miss anything?

the diodes read, from what i can tell:
FR154
DC
that number does not come up on digikey, but on the 1200bp schematic, it lists "PR1504" as the diodes used, and those do come up. should i use the pr1504's? is there a reference that shows how to decode the print into that number?.. oh wait, i just noticed that it is a non-stock item. is there a good part number that i can use?

the original complaint of this amp was that it just put out nothing but static, which kind of makes sense, not getting enough power to the regulators, and no filtering. all i have tested as of yet, are the winding and traces from the top-side and all appear well. i also did an ohm check on the regulators, which appeared okay.

thanks again for your help,
-Heath H-
  Reply With Quote
Old 21st November 2012, 01:05 PM   #10
diyAudio Member
 
Join Date: Nov 2003
Location: Louisiana
Mouser has the originals but if you want to order from DK, the BYV28-200-TAPCT-ND is a good sub for this application. The BYV-28 is good for most instances where you need a fast efficient, relatively high-current diode in a small package. If the originals aren't defective, you don't need to replace them.

The electrolytic capacitors will likely need to be replaced. The FC series of capacitors is a good choice.
P10316-ND (check lead spacing)

If/when you replace the diodes/resistors, install them so that they're about 1/4" above the board. That will prevent them from doing further damage to the board. Using larger resistors will also reduce the operating temperature.

Last edited by Perry Babin; 21st November 2012 at 01:11 PM.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
DIRECTED 600D mike49504 Car Audio 2 17th November 2012 01:36 AM
MTX 600D Q2 type, p.n. -missing from the pcb DAKOS Car Audio 5 3rd February 2009 02:57 AM
Strange (to me) resistor schematic markings sepulchre Parts 5 5th October 2008 03:16 PM
RtR 600D The_Mox00 Multi-Way 10 15th October 2006 11:49 PM
Krell KSA 100 schematic, resistor value question blueman Solid State 28 20th February 2004 03:44 AM


New To Site? Need Help?

All times are GMT. The time now is 07:52 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2