Punch 75HD Only One Channel Plays - diyAudio
Go Back   Home > Forums > General Interest > Car Audio

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 13th October 2012, 05:12 PM   #1
diyAudio Member
 
Join Date: Oct 2012
Default Punch 75HD Only One Channel Plays

Only the right channel plays. If i connect the left channel (-) to the right channel (-), i also get music.

All voltages are good at the points labeled on the schematic. I do not have a scope. Any Suggestions?

I have replaced all supply/output transistors and the HBPIM
  Reply With Quote
Old 13th October 2012, 05:48 PM   #2
diyAudio Member
 
seankane's Avatar
 
Join Date: May 2010
Location: Washington State
Confirm all the source resistors are within tolerance.

Confirm there are no cold solder joints on the speaker plug.

Confirm the rca input jack is not loose internally, sometimes you have to solder the shield to the mounting frame.

If you are using the factory harness bypass the fuses in the speaker plug to confirm there is not a bad connection there.

Confirm there are no issues on the HB-PPM or the HB-POM.

Does the channel bias properly?
__________________
Pyramid 52 Amp Power Supply----Fluke 787 Processmeter----Tektronix 465 Scope----Velleman HPS40 Scope----Soldering Iron----Desoldering Iron----Hejet HJ 500-S Heatgun----DM4070 Digital LCR Meter----Propane Torch
  Reply With Quote
Old 13th October 2012, 05:57 PM   #3
diyAudio Member
 
Join Date: Oct 2012
Ok, I'll do what you suggested

Can you tell me how to bias correctly? I read up that rockford wants 4 to 5 mv across the source resistors, but i get nowhere near that with my red and black leads on both sides of the source resistors and meter set to mv
  Reply With Quote
Old 14th October 2012, 04:39 AM   #4
diyAudio Member
 
Join Date: Nov 2003
Location: Louisiana
If your 12v power supply has an amp meter, you can set it as is shown in the following demo.
http://www.bcae1.com/temp/ausettingbias.swf

Setting it with the voltage across the 0.1 ohm source resistors requires that you monitor the voltage and slowly turn the bias pots clockwise. This is done with no speaker load and no signal input. I feel that 4-5mv is too much and will make the amp run hotter than it needs to. It won't harm anything but it doesn't need to be set that high. 1mv is generally good enough.

If the right channel plays but it doesn't play bridged, there is likely a bad connection between the speaker and the terminal block on the amp. If it has brown/black fuse holders, they have a tendency to become intermittent as the terminal in the holder is pulled too deeply into the holder. I think this is why it was suggested that you bypass the fuse holders.
  Reply With Quote
Old 18th October 2012, 06:16 PM   #5
diyAudio Member
 
Join Date: Oct 2012
Problem Found: The left board HB3 (HB-POM) has one small transistor missing on the board. That's why I don't get sound from that side. Now i need a new HB-POM...
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Punch 500a2 messed up channel brandes.cm Car Audio 50 10th April 2012 12:31 AM
Rockford Fosgate Punch 75HD seankane Car Audio 5 18th July 2011 12:49 AM
Punch 500a2 distorted channel chipper Car Audio 62 21st March 2011 09:02 PM
Punch 40DSM no output on either channel brandes.cm Car Audio 33 27th June 2010 04:52 AM
rockford fosgate punch 200ix transformer plays music? spooney Car Audio 2 15th October 2007 12:04 AM


New To Site? Need Help?

All times are GMT. The time now is 10:29 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2