diyAudio

diyAudio (http://www.diyaudio.com/forums/)
-   Car Audio (http://www.diyaudio.com/forums/car-audio/)
-   -   Jl Audio G1700 4 cap blow (http://www.diyaudio.com/forums/car-audio/214336-jl-audio-g1700-4-cap-blow.html)

kalacho2006 12th June 2012 07:00 AM

Jl Audio G1700 4 cap blow
 
Hi, I have this amp jl audio, I buy from a friend, the amplifier showed no signs of life, then proceeded to open it and found burned four capacitors of 2200uf 25v 105degress and a track to open the transformer all the componets look good and the diode trans is good.

http://img831.imageshack.us/img831/3390/jlaudiocap.jpg I then proceeded to repair the 2200uF 50V capacitor components 4 105 degrees and weld the track making this the amp on but as you want to protecion mode but nothing more, no audio and power leds and protecion, flash


this is the pic of the complete amp

http://img703.imageshack.us/img703/3137/img0190kg.jpg

Perry Babin 12th June 2012 10:59 AM

Are the legs on any of the heatsink mounted components broken? You may have to twist them slightly to see the break if they are broken.

What are you using for a power supply?

Do you have a scope?

kalacho2006 12th June 2012 01:59 PM

not, not legs broken i put out the board and nothing,i'm using a 12 v battery of my children power wheel and i only use a multimeter not scope on my hands.

Perry Babin 12th June 2012 09:40 PM

JL audio amplifiers are very sensitive to voltage. If the amp is causing an instantaneous voltage drop (not visible by using a multimeter), it could be causing the amp to go into protect.

kalacho2006 13th June 2012 01:00 AM

The 4 new caps can cause the drop voltages?
Because when I replace 2 of they are nichicon and 2 unknow brand (kmc) and double of voltage 50v.

Perry Babin 13th June 2012 03:22 AM

If the 12v supply (battery in this instance) has too much internal resistance or insufficient capacity, the 12v will drop. This has nothing to do with the capacitors in the amp.

kalacho2006 20th June 2012 11:00 PM

ok, I use a car battery to check again the amplifier and same problem, amp turn on but the protection led flash,cheking the board i noticed 4 leds on the board not power on and others yes, maybe the circuit not power on is fail, i noticed too 2 op amp JRC 2082 and 2068 on the yellow strip under the pot are heat at touch, all the board are cool only this 2 components are heat. some ideas where start ?
http://img7.imageshack.us/img7/9277/img0190sd.jpg

Perry Babin 21st June 2012 12:29 AM

Measure the DC voltage with the black probe on pin 4 and the red probe on pin 8. Post the voltage on both ICs.

kalacho2006 27th June 2012 07:59 PM

Hey perry how much for repair this amp for me? I can send to you and pay shipping costs.

Perry Babin 27th June 2012 08:01 PM

I'm not taking anything in at this time. I won't likely catch up until August.


All times are GMT. The time now is 04:59 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio


Content Relevant URLs by vBSEO 3.3.2