Memphis mojo orange flame

timwebb · 25th October 2011, 11:15 PM

do anyone know the placement for the output transistors in this amp? thanks!

Perry Babin · 26th October 2011, 12:47 AM

You need to provide exact model numbers or a good quality photo when asking for help.

16-MC2000D?

timwebb · 26th October 2011, 12:56 AM

yes.

Perry Babin · 26th October 2011, 01:08 AM

Use your multimeter to find all of the output transistors that have the 3rd pad directly connected. There will be two groups. The group with more transistors is for the P-channel outputs. The others are for the N-channel outputs. All of the 0.02 and 0.04 ohm current sense resistors will have to be intact/within tolerance for this to work.

timwebb · 27th October 2011, 02:17 AM

ok i figured out where they go. the 640's are over heating. and i can hear a frying sound from the yellow inductor in the middle. would a bad inductor make the output over heat?

Perry Babin · 27th October 2011, 04:08 AM

Are they supposed to have IRF640s in that amp? Many of these amps (or at least amps similar to these) used IRFB31N20Ds in place of the 640s. The 640s I've tried (for testing) all ran hot. Do NOT buy IRFB31N20Ds from ebay unless you KNOW the seller to be legitimate. Too many people have purchased the IRFB31N20D from ebay and they were counterfeit or otherwise not up to spec and caused a variety of problems.

timwebb · 27th October 2011, 10:36 AM

The amp has been worked on by several people.so most parts are not the own parts. I was looking at a directed 2400 that I just got and it uses those transistors in place of the 640's. I also need the place ment of the ic's in the preamp section.the ic behind the rca jacks is missing. I will up load pictures when I'm off work.

Perry Babin · 27th October 2011, 10:49 AM

The IC behind the RCA jacks was a KIA4559. It's not widely available. Install a socket and a TL072 for now. An LM4558 may work but they can be unstable.

timwebb · 31st October 2011, 02:11 AM

i got the amp to power up. i replaced alot of the bad transistors on the driver cards and 1ohm resistors. but when ever i install both cards both lights comes on and stay on. i cant find what im missing.

Perry Babin · 31st October 2011, 07:26 AM

What happens when you install only one driver board?

25th October 2011, 11:15 PM	#1
timwebb diyAudio Member Join Date: Jan 2010 Location: memphis tn	Memphis mojo orange flame do anyone know the placement for the output transistors in this amp? thanks!

26th October 2011, 12:47 AM	#2
Perry Babin diyAudio Member Join Date: Nov 2003 Location: Louisiana	You need to provide exact model numbers or a good quality photo when asking for help. 16-MC2000D? __________________ Links >> Basic Car Audio Amp Repair --- Basic Car Audio Electronics --- Basic Transistor Testing --- Basic Switching Power Supply Design --- Basic Computer Skills << Links

26th October 2011, 01:08 AM	#4
Perry Babin diyAudio Member Join Date: Nov 2003 Location: Louisiana	Use your multimeter to find all of the output transistors that have the 3rd pad directly connected. There will be two groups. The group with more transistors is for the P-channel outputs. The others are for the N-channel outputs. All of the 0.02 and 0.04 ohm current sense resistors will have to be intact/within tolerance for this to work. __________________ Links >> Basic Car Audio Amp Repair --- Basic Car Audio Electronics --- Basic Transistor Testing --- Basic Switching Power Supply Design --- Basic Computer Skills << Links

27th October 2011, 04:08 AM	#6
Perry Babin diyAudio Member Join Date: Nov 2003 Location: Louisiana	Are they supposed to have IRF640s in that amp? Many of these amps (or at least amps similar to these) used IRFB31N20Ds in place of the 640s. The 640s I've tried (for testing) all ran hot. Do NOT buy IRFB31N20Ds from ebay unless you KNOW the seller to be legitimate. Too many people have purchased the IRFB31N20D from ebay and they were counterfeit or otherwise not up to spec and caused a variety of problems. __________________ Links >> Basic Car Audio Amp Repair --- Basic Car Audio Electronics --- Basic Transistor Testing --- Basic Switching Power Supply Design --- Basic Computer Skills << Links

27th October 2011, 10:49 AM	#8
Perry Babin diyAudio Member Join Date: Nov 2003 Location: Louisiana	The IC behind the RCA jacks was a KIA4559. It's not widely available. Install a socket and a TL072 for now. An LM4558 may work but they can be unstable. __________________ Links >> Basic Car Audio Amp Repair --- Basic Car Audio Electronics --- Basic Transistor Testing --- Basic Switching Power Supply Design --- Basic Computer Skills << Links


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

27th October 2011, 02:17 AM	#5
timwebb diyAudio Member Join Date: Jan 2010 Location: memphis tn	ok i figured out where they go. the 640's are over heating. and i can hear a frying sound from the yellow inductor in the middle. would a bad inductor make the output over heat?

27th October 2011, 10:36 AM	#7
timwebb diyAudio Member Join Date: Jan 2010 Location: memphis tn	The amp has been worked on by several people.so most parts are not the own parts. I was looking at a directed 2400 that I just got and it uses those transistors in place of the 640's. I also need the place ment of the ic's in the preamp section.the ic behind the rca jacks is missing. I will up load pictures when I'm off work.

31st October 2011, 02:11 AM	#9
timwebb diyAudio Member Join Date: Jan 2010 Location: memphis tn	i got the amp to power up. i replaced alot of the bad transistors on the driver cards and 1ohm resistors. but when ever i install both cards both lights comes on and stay on. i cant find what im missing.

31st October 2011, 07:26 AM	#10
Perry Babin diyAudio Member Join Date: Nov 2003 Location: Louisiana	What happens when you install only one driver board? __________________ Links >> Basic Car Audio Amp Repair --- Basic Car Audio Electronics --- Basic Transistor Testing --- Basic Switching Power Supply Design --- Basic Computer Skills << Links

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Schematics for Memphis Mojo 16-MCD 4KW	Deadly Sones	Car Audio	1	7th May 2011 04:14 PM
memphis 2000 mojo	timwebb	Car Audio	10	6th March 2011 04:32 PM
Memphis MOJO 16-MCD4KW	mike49504	Car Audio	17	23rd February 2011 10:17 AM
memphis mojo driver card	timwebb	Car Audio	13	1st May 2010 10:46 PM
need help with my 12' memphis mojo m3	aphillyated	Car Audio	6	25th December 2006 08:54 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read