diyAudio

diyAudio (http://www.diyaudio.com/forums/)
-   Car Audio (http://www.diyaudio.com/forums/car-audio/)
-   -   slot porting (http://www.diyaudio.com/forums/car-audio/111996-slot-porting.html)

skooter 16th November 2007 04:46 AM

slot porting
 
Is it possable to slot port a wedge box? Box is ( 41" long, top is 6.5 deep, bottom is 12" deep, and is 13" tall ) Thanks.

jol50 16th November 2007 03:43 PM

I imagine, I had a kicker truck box with a single 10 in it that had a port across the bottom that came out the side. I guess it depends on what you mean by slot.

shagone 16th November 2007 08:29 PM

you could possibly do it if you can manage to get the correct port length and width calculated to fit properly. the ports might have to be firing off to the sides towards the rear of the box and you might run into clearance issues on the outside for the port to breath properly.

or maybe you could slot port it straight up the top of the box but in that case you could just use flared round ports.

are you going for high SPL or sound quality? depending on your subs (and amp) you might be better off with a simple sealed box for sound quality if your subs will work correctly sealed in your given box volume and your amp has decent power to push them. This is just my opinion and the opinion of many others as well.

skooter 16th November 2007 09:38 PM

wel as of right now I am looking a a set of 10" alpine subs and I am fixin to get a Persision Power PCX-2200 amp to run them. I listen to mostly metal, rock, and some times pop or something in the bumping music line.

shagone 16th November 2007 09:49 PM

in my opinion, for metal, rock, and pop sealed is the way to go! easier and cheaper to build too.

skooter 16th November 2007 10:18 PM

do you know anything about these amps? Prisision Power PCX-2200? thanks.

jol50 17th November 2007 12:04 AM

Old Precision Power (PPI) are said to be good amps, I have a 150w one that works well. Not familiar with the newer ones but for subs I'll use anything that works....unlike the high side.

Sealed box will be smallest in general. You really need to figure out what you want to tune the box to for Hz, for SPL/SQ or between. Then see what size box the sub you want needs and if that fits your space. You can d-load winISD free and put the sub specs into it to get an idea, or most subs say in the manual/on their site what size works well. You have to make it the right size for that sub to get the most out of it at the tuning you want.

You can port any box, but it will be larger than sealed for the same driver/tuning. You can hardly ever port an existing sealed box and have it work right without making it larger or changing drivers.

skooter 17th November 2007 12:22 AM

buddy has a few other amps as well for sale. Profile AP1200, and a Profile AP1000M, he talks highly of them. are the a decent amp as in middle of performance?

shagone 17th November 2007 12:32 AM

profile is middle of the road but the precision would probably be better.

ppia600 18th November 2007 02:27 PM

Get the ppi, if it has the specs you said were on the box.. its one of the good ones.


All times are GMT. The time now is 11:33 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio


Content Relevant URLs by vBSEO 3.3.2