diyAudio - RIAA
Go Back   Home > Forums > Blogs > RJM Audio Blog
Home Forums Rules Articles diyAudio Store Gallery Wiki Blogs Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
If I put my notes here, I might be able to find them again later!
RIAA Phono stage circuit design.
Old

CrystalFET 2 MM passive phono preamplifier with JFET amplification

Posted 21st April 2017 at 01:05 AM by rjm (RJM Audio Blog)
Updated 21st April 2017 at 04:44 AM by rjm (revised to 2.0g (capacitors C9 and C10 misslabelled))

In hindsight the original CrystalFET suffered from overreach. To obtain the 55 dB midband gain required for an MC phono stage lots of other things I might have wanted to build into the design like degenerative feedback were discarded.

Degenerative feedback as it applies to JFET amplifiers is the practice of leaving the source resistor partially or completely unbypassed. It reduces the voltage gain, but linearizes the dynamic operation of the amplifier - coercing the gain to the ratio of the source and drain resistors rather than leaving it defined by the JFET transconductance. The circuit gain can then be fixed by the designer without worrying so much about matching devices.

The CrystalFET circuit is a traditional two stage passive photo preamplifier design, the only novelty here is the addition of a second JFET configured as a source follower to each amplifier stage. To obtain above 50 dB gain no degenerative feedback could be used, and the JFETs had to be not...
Attached Thumbnails
Click image for larger version

Name:	pcb-crystal-20g-sch.png
Views:	192
Size:	9.9 KB
ID:	2347   Click image for larger version

Name:	pcb-crystal-20g-brd.png
Views:	111
Size:	35.5 KB
ID:	2348   Click image for larger version

Name:	crystal20g.png
Views:	84
Size:	142.5 KB
ID:	2349   Click image for larger version

Name:	crystal20-response.png
Views:	79
Size:	20.9 KB
ID:	2353  
Attached Files
File Type: zip Crystal-20g.zip (63.3 KB, 49 views)
File Type: zip pcb-crystal-20g-bom.zip (220.3 KB, 50 views)
File Type: asc Crystal 20.asc (5.2 KB, 100 views)
rjm's Avatar
rjm
diyAudio Member
Views 312 Comments 0 rjm is offline
Old

VSPSX phono stage design idea

Posted 24th June 2016 at 12:48 AM by rjm (RJM Audio Blog)
Updated 18th April 2017 at 11:15 PM by rjm

The original VSPS is getting up in years, and could do with a bit of an update.

The VSPSX adds the foursquare shunt-source voltage regulator and bboard v2.1 output buffer.

Development thread here.

[updated attached content to rev. 1.0a4]

Two mistakes in previous BOM:

C4 was a 5mm lead spacing Wima MKP but the board spacing is only 2.5mm. The part is changed to Wima MKS with 2.5mm lead spacing.

R22,23 was incorrectly given as 47.5k, it should have been 4.7k and has been since updated to 10k. This is not a critical value, the circuit will work with any of the resistances.

[further work]

The boards have been revised to 1.2a. The new design is posted to the development thread.
Attached Thumbnails
Click image for larger version

Name:	pcb-vspsx-10a-brd.png
Views:	107
Size:	21.0 KB
ID:	2094   Click image for larger version

Name:	vsps-10a-gerber.png
Views:	102
Size:	207.3 KB
ID:	2096   Click image for larger version

Name:	DSC_6187_01 sm.jpg
Views:	96
Size:	361.6 KB
ID:	2107  
Attached Files
File Type: asc VSPSX-10a.asc (13.4 KB, 90 views)
File Type: zip pcb-vspsx-10a4-bom.zip (168.8 KB, 12 views)
rjm's Avatar
rjm
diyAudio Member
Views 591 Comments 0 rjm is offline
Old

CrystalFET Phono Stage

Posted 3rd March 2016 at 04:55 AM by rjm (RJM Audio Blog)
Updated 21st April 2017 at 01:46 AM by rjm

Development thread here. Web page here.

CrystalFET is a J113 jfet-based two-stage phono preamp, with passive equalization and on-board MOSFET-based shunt voltage regulator.

Jfets Q1 and Q3 should be matched between channels, and for best results the value of drain resistors R2 and R9 should be selected based on the jfet pinch off voltage of Q1 and Q3 respectively.

rev. 1.4e (final version) removes some unneeded resistors and tidies up the board layout a little. The resistors have been renumbered.
Attached Thumbnails
Click image for larger version

Name:	IMGP6761.jpg
Views:	513
Size:	263.9 KB
ID:	1889   Click image for larger version

Name:	IMGP6764.jpg
Views:	266
Size:	192.5 KB
ID:	1890   Click image for larger version

Name:	DSC_6236.jpg
Views:	271
Size:	262.8 KB
ID:	1897   Click image for larger version

Name:	crystalFET 1.3a response.png
Views:	198
Size:	22.7 KB
ID:	1934   Click image for larger version

Name:	pcb-crystal-14e-sch.png
Views:	434
Size:	18.3 KB
ID:	2007  

Click image for larger version

Name:	pcb-crystal-14e-brd.png
Views:	253
Size:	18.5 KB
ID:	2008   Click image for larger version

Name:	CrystalFET-14e.jpg
Views:	157
Size:	394.8 KB
ID:	2023  
Attached Files
File Type: zip pcb-crystal-14e-bom.zip (246.7 KB, 51 views)
File Type: asc Crystal 14.asc (11.2 KB, 149 views)
rjm's Avatar
rjm
diyAudio Member
Views 2012 Comments 6 rjm is offline
Hide this!Advertise here!

New To Site? Need Help?

All times are GMT. The time now is 10:12 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999-2017 diyAudio

Content Relevant URLs by vBSEO 3.3.2
Wiki