The B-board line buffer is back from the fab and running on the bench.

Cute little board. Diamond buffer with BD-135/136 transistors and a built in Z-reg. Designed to buffer the output of op amp circuits to help drive cables and otherwise isolate the op amp feedback loop from the big bad outside world. It can also be used as a unity gain preamplifier, or, with by changing a couple of resistors and adding small heatsinks, to drive headphones.

Development thread here.

UPDATE: Also finished a second set of boards, configured as a headphone driver (5x bias current, heatsinks).

A real, honest-to-goodness voltage regulator has three parts: a fixed voltage reference, an error amplifier, and a pass element.

Most people only put eyeballs on the final, all-wrapped-up-in-a-tidy-IC-package version, typified by the LM7812, or with a couple of extra gain-set resistors, the LM317. These chips have a working bandwidth about about 2 kHz, as they are designed to 1) reduce 120 Hz ripple and 2) be rock stable no matter what abuse they are subjected to. As a result at audio frequencies and above they are pretty much noise generators...

Knowing this, many people have set out to build better regulators for audio work.

The most obvious route is to build a high performance LM7812 from discrete components. (Most excellent review here.) AD797 for the error amplifier, high stability, low noise voltage reference, etc. The trick though, is stability. The LM7812 is low bandwidth not because it's too cheap to manage anything better, but because...

I have been doing a web-dredge, searching for simple, single supply, transistor buffer/gain stages, preferably FET-based.

This one seems interesting.

The designer, Henry Nurdin, has kindly posted a full schematic.

Ignore the fact for a moment that it's designed as a tiny battery-operated module to retrofit into electric guitars, the basic circuit block with 5-6 dB non-inverting gain could be used as a front end for a headphone buffer stage like, I'm thinking especially, the Szekeres MOSFET buffer.

That's if the bandwidth is sufficient for high-end audio (should be!?) and, slightly more worrisome, acceptable gain matching between channels can be achieved without resorting to trim pots.

This circuit reminds me of something. ... Sziklai pair? Time to do some more dredging...

Ah, bingo!

Update:

And with some jiggery-pockery this is taking shape as a (yet another) headphone amplifier....

File this under "things-I-should-have-learnt-to-do-many-years-ago-but-was-too-lazy-to-bother".

Many pcb fab outfits that do business with hobbyists and DIYers choose to accept Eagle .brd files, which means they do the conversion to Gerber output so you don't have to. I've relied on that for far too long, but when an error showed up in one the .pdf proofs on the last batch of boards I sent out for fabrication, they asked me to send the Gerber files instead. So I bit the bullet and after a couple of false starts managed to give them what they wanted. Looking back at it, it was easy and something I should have learnt, as I wrote up above, years ago, but, for posterity, here's how it's done:

(In Eagle 6.1, on Windows Vista)

1. Make a working folder for the Gerber files.
2. Copy the Eagle board (.brd) file to this directory.
3. Open Eagle (version 6.1)
4. Select menu item "file/open/CAM job"
5. The open file dialog appears, defaulting to

...

Finally got around to some more comparison listening with the Sapphire headphone amplifier. To recap: the circuit has an open loop diamond buffer output, so the op amp is just providing voltage gain. It configured for a non-inverting gain of 21 dB to match my 300 ohm HD600 headphones. Pretty much textbook operating conditions.

The op amp inputs are impedance balanced at about 1 kohm. This is about the crossover point where you start thinking about using FET input stages, but BJTs should still be fine.

I'm interested to see if there is a definite signature to a FET-input opamp. The original build called for an OPA134, which is a JFET input circuit. I tried the OPA27, which is a low-noise, high-input-current BJT design, and last night I tried the NE5534A, a classic general purpose audio opamp with bipolar inputs.

I've long been in agreement with Douglas Self on the NE5532/NE5534 : anyone who reports these op amps sound bad is either not using...

I was asked to suggest a voltage regulator for the First Watt (Pass DIY) B1 buffer. One thing led to another and the next thing I'd sketched up a circuit board for the buffer as well as the regulator.

It's like a B-board, but with the JFET buffer instead of the diamond buffer, and with a single supply and, hence, the coupling caps front and back. Since it's using JFETs for the buffer I used a JFET for the pass device in the regulator, too.

Full credit to Nelson Pass for his design.

Eagle files do not show 2SK170 because the package is not in Eagle. All transistors 2SK170 or equivalent. Zener is 18-22V DO35 or DO41 i.e. Vishay BZX85. V++ is 5-15 V above whatever you select the Zener reference to be.

This is a followup of sorts to the X-reg, though there is nothing original about the circuit this time around.

It's just a Zener voltage regulator with a series pass transistor. I lifted this particular configuration from the Pionner C-21 preamplifier and re-tuned it for op amp applications. My main interest here is trying to make a small and convenient board layout.

I've used this circuit block already in the Sapphire amp and come away impressed.

The output is about 1 V less than the Zener voltage, and the input voltage should be about 3-6 V above the Zener reference voltage. I'm working here with 17 V unregulated supply and 12 V Zeners, but the values can be reconfigured easily enough for any output from 4-24 V

This is a low current circuit. If you are just powering a few op amps, no heatsinks are needed. Above 25 mA small heatsinks are a good idea. The circuit is not designed for output currents above 100 mA.