Adding TentLabs XO2.2 low jitter clock to exposure 2010S CD player - diyAudio
Go Back   Home > Forums > Blogs > My DIY projects

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
I returned to DIY electronics in 2009 after a 20 year pause by building a few kits to get in shape. This blog is for me to keep track of my progress.
Rate this Entry

Adding TentLabs XO2.2 low jitter clock to exposure 2010S CD player

Posted 9th April 2013 at 11:03 AM by alexcp
Updated 12th May 2013 at 04:58 PM by alexcp (Added photos, links)

I added a TentLabs XO2.2 low jitter clock and a separate power supply for it to my exposure 2010S CD player. The process was very straightforward - see the pictures.

The exposure 2010S CD player has an easy internal layout, where most of the components sit on a large PCB.

The original clock is based on the 74HC04N chip located in the middle of the PCB, to the left from the three white power connectors connecting the toroidal transformer. A close-up picture shows the crystal resonator wrapped in a black heat-shrink tube, two 33pF capacitors on each side of the resonator (those with black dots on top), and a resistor R75, which also serves in the circuit. The oscillator is built on the single invertor (pins 13 and 12 of the IC).

The original clock is generating 16.9344 MHz at 5V CMOS levels.

To install XO2.2, I removed the resonator and the capacitors, leaving the resistor in place. I connected the signal cable from XO2.2 to the pads of the capacitor that is closer to the pin 14 of the IC; of the two 33pF capacitors, it is the farthest from the front of the CD player. Then I glued the XO and the power supply boards to the right of the main board, closer to the front panel. I could probably drill the bottom plate and use screws, but I didn't.

The power supply is connected to the mains switch with two wires (red on my photo) that go along the front panel near the bottom and are soldered to the small PCB holding the on/off switch on the left side of the panel.

That's it! It took me maybe two hours altogether.

My impression is that with the XO, the sound became richer in details and more transparent, with better spatial resolution. Obviously, this is very subjective; no double-blind comparison could be performed on just one CD player being modified.

P.S. I also had to replace the "analogue output" double PCB mounted RCA connector, as its ground pin broke. I installed two panel mounter RCAs, seen in the photo.
Attached Thumbnails
Click image for larger version

Name:	IMG_0111.jpg
Views:	2742
Size:	191.2 KB
ID:	937   Click image for larger version

Name:	IMG_0112.jpg
Views:	588
Size:	152.7 KB
ID:	938   Click image for larger version

Name:	IMG_0113.jpg
Views:	1092
Size:	151.6 KB
ID:	939   Click image for larger version

Name:	IMG_0114.jpg
Views:	358
Size:	173.4 KB
ID:	940   Click image for larger version

Name:	IMG_0115.jpg
Views:	772
Size:	220.2 KB
ID:	941  

Click image for larger version

Name:	IMG_0116.jpg
Views:	343
Size:	186.6 KB
ID:	942   Click image for larger version

Name:	diyaudio13.jpg
Views:	456
Size:	167.1 KB
ID:	1020   Click image for larger version

Name:	diyaudio16.jpg
Views:	302
Size:	219.9 KB
ID:	1021   Click image for larger version

Name:	diyaudio28.jpg
Views:	311
Size:	230.9 KB
ID:	1022   Click image for larger version

Name:	diyaudio30.jpg
Views:	345
Size:	154.8 KB
ID:	1023  

Posted in Digital Sources
Views 1472 Comments 0 Email Blog Entry
Total Comments 0

Comments

 
Hide this!Advertise here!

New To Site? Need Help?

All times are GMT. The time now is 02:22 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2