diyAudio - Entries for March 2014
Go Back   Home > Forums > Blogs > abraxalito

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Old

Hexacap-based Ozone DAC

Posted 20th March 2014 at 03:18 AM by abraxalito
Updated 31st March 2014 at 01:07 AM by abraxalito

Here's my current bench lash-up DAC based on three hexacaps. Total capacitance of the order of 1.3F.

32fs EIAJ is fed in, balanced, from the left, the central hexacap feeds two TDA1545ATs. Filters are TDK inductor based, six stage balanced with X7R caps (gasp!). Caps in the centre provide the mid-rail power (2.5V) which the I/V resistors are fed from. The two hexacaps on the right power the post amps based on AD815ARBs, gain set roughly to 26dB with a little NOS droop correction. They're the postage-stamp sized boards roughly in the middle. Output is differential and fed to ferrite-cored transformers to convert to SE.

I'm blown away by the dynamics of this, given the right recording. Next up is an amp based on paralleling 8 or 10 AD815s. Each fed from its own hexacap, of course....

Update1 - the DAC supply has now been upgraded to two tiers of the 4700uFs, interconnected by six 1.5mm diameter solid copper wires. Capacitive reactance measures 2.5mohm...
Attached Thumbnails
Click image for larger version

Name:	P1010092.JPG
Views:	243
Size:	713.7 KB
ID:	1260  
abraxalito's Avatar
diyAudio Member
Views 538 Comments 16 abraxalito is offline
Old

Adventures in low impedance power supplies

Posted 10th March 2014 at 08:01 AM by abraxalito
Updated 17th May 2014 at 03:52 AM by abraxalito

Here's my latest crazy project, intended to answer the question 'How low can you go?' in power supply impedance. No listening tests yet, I've just finished assembling this stack of hexagon capacitor arrays out of cheap electrolytics. Total capacitance of the top 4 tiers is comfortably above 1F. The top tier is designed for lowest ESR at HF using Nichicon 1500uFs, the next tier is a trade between ESR and uF. The last two are the highest capacitance density I could find (a total of 182 4700uFs). I've yet to connect the bottom two hexagons to the upper tiers but the top two are connected by wires running through the gaps between caps.

The whole is intended to push the limits of low frequency noise in powering a couple of TDA1545s which will sit on a small PCB supported on thick wires from the centre of the top tier. I am aiming to get a capacitive reactance (at 50Hz) at the DAC supply pins below 3mohm and ESR below 1.5mohm.

Update1 : connected the bottom two tiers...
Attached Thumbnails
Click image for larger version

Name:	wedding-cake.JPG
Views:	234
Size:	691.1 KB
ID:	1253   Click image for larger version

Name:	OST4700uF.jpg
Views:	100
Size:	171.7 KB
ID:	1254   Click image for larger version

Name:	5captier.JPG
Views:	146
Size:	673.4 KB
ID:	1255  
abraxalito's Avatar
diyAudio Member
Views 512 Comments 4 abraxalito is offline
Hide this!Advertise here!

New To Site? Need Help?

All times are GMT. The time now is 07:50 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2