AC Mains Controller now available! - diyAudio
Go Back   Home > Forums > Commercial Sector > Manufacturers > Aussie Amplifiers

Aussie Amplifiers High quality, high performance amplifier modules and accessories

Reply
 
Thread Tools Search this Thread
Old 24th August 2012, 12:58 AM   #1
diyAudio Member
 
Join Date: Jul 2002
Location: Launceston, TAS, Australia
Default AC Mains Controller now available!

The main function of the mains controller is to provide easy powering on and off of mains power
without the need of a heavy duty mains switch, but allows you to use a low power low voltage rated switch
of which there are many available or it can be enabled via the common 12v trigger voltage found on many commercial pre amps.
For safety and isolation the 12 volt trigger is opto-isolated.
One of the more nicer features is the addition of a DC offset detection circuit which can monitor six amplifier outputs concurrently. These monitored inputs can also be used for thermal, over current, over voltage protection.
In the event of an amplifier fault the detection circuit will latch and power down the amplifiers power supply instantaneously, removing the need for loudspeaker protection for each amplifier channel and immediately protecting the power amplifier from further damage.
The HPA-Power one main board is self powered via a high quality encapsulated 4VA mains transformer and has power on and protection status LEDs which can be extended off board to the power amplifier front panel.

Click the image to open in full size. Click the image to open in full size.



The PCB size is 95mm x 90 x 20mm. Price is $139.00AUD.

Click the image to open in full size.


Cheers

Anthony
Aussie Amplifiers

Last edited by The Saint; 12th September 2012 at 12:32 AM.
  Reply With Quote
Old 12th September 2012, 12:38 AM   #2
diyAudio Member
 
Join Date: Jul 2002
Location: Launceston, TAS, Australia
Here is some key features for the Power One controller.


HPA-Power One - Key Features.
30 amp contact rated output relay.
Switch up to 4KVA Power Transformers.
Opto-Isolated 12v Trigger for power on, low power manual switch optional.
Built-in 6 channel amplifier DC offset fault detection.
If DC offset fault is detected in any one of the monitored channels, power is turned off instantly.
Can also be used to monitor for over-temperature using a normally open thermal switch.
Other fault detection using external sensing are possible, such as Over-Voltage, Over-Current, etc.
Compatible with 220-240VAC and 110-120VAC 50/60hz Mains supply
World Wide Compatibility !
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Distortion in ac mains supply ? percy Power Supplies 19 15th March 2012 01:19 AM
high AC mains problem atenolol50 Tubes / Valves 7 25th September 2008 04:11 PM
SMPS that runs off AC mains LBHajdu Power Supplies 2 4th March 2005 05:00 PM
9V AC Mains Adapter for UK Blue_Max Parts 0 13th November 2004 11:38 PM
AC mains filtering question thylantyr Solid State 4 26th March 2003 08:28 PM


New To Site? Need Help?

All times are GMT. The time now is 03:43 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2