PDA

View Full Version : Chip Amps


Pages : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 [20] 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41

  1. K50 lm1875 feedback resistor distortion
  2. iSub Chip?
  3. LM3876TF based sony amp, bridging ?
  4. How many 3886 chips required to drive these woofers?
  5. LM3886 Ground Loop Noise - Solutions?- Car Amp Application
  6. National LM3886TF or not?
  7. can you make LM3876 work in Class A ?
  8. Trafo question...
  9. Test bulb is on. Need help with BrianGT's LM3875.
  10. My Bridged LM3886
  11. small amp out of TA8227P
  12. Hello, can i have some help please?
  13. MY_REF EVOLUTION by MAURO PENASA
  14. LM3886 and +-42V
  15. OPA549/541 at unity gain - schematic needed.
  16. Newb wonders: Class T or Gainclone better for monitoring?
  17. lm4780 eagle library
  18. Alternative OPA134 manufacturer or a fake chip?
  19. What resistor and potentiometer values for GC shunt volume control?
  20. New boards on the way, BPA300
  21. 6 channel digital volume control
  22. newbie seeking info about homemade ipod amplifier
  23. Variac as transformer for LM4780 GC?
  24. New design help
  25. worst CMRR?
  26. My GIFT for you: TDA7293 board + extras
  27. Replace DRV134 with OP-amp
  28. Transformer load on mains circuit
  29. Transformer for Gainclone
  30. TDA7293 amp @ 8Ohms load @ 42v rails
  31. Which parameter of the filtering caps do influence the sound of a gainclone???
  32. choosing gain in LM3886
  33. Choosing the right chip amp for home theater.
  34. Interfacing to a digital IC on a separate 5v supply
  35. lm3886 guitar amp?
  36. Power Supply problem
  37. My LM3886 Integrated Amp
  38. tube/op amp/class A buffers
  39. Pre-Amp for Chip-Amp?
  40. parallel TPA6120?
  41. contacting chipamp.com
  42. Distributed Amplifier questions
  43. kit newbie looking for advice
  44. Mains pops and clicks
  45. Question about chip amp with different type of transformers???
  46. Never made anything before
  47. Clipping and amp power supply
  48. Total VA Available on Multiple Tap secondary?
  49. what went wrong?
  50. Question re: LM3886 Snubber pin connections
  51. which tone control circuit?
  52. Multiple secondaries toroid
  53. Problems designing an PSU for an gainclone.
  54. LM3886 vs TDA7294
  55. best buffer gainclone transistor need
  56. Svideo cable for audio interconnectors.
  57. Hum on BrianGT kits.....
  58. BrianGT boards....replacing a few parts?
  59. first Amp
  60. Help with a very simple 2002/383 audio amp
  61. DC offset when turning amp off....
  62. Confusion about LM3886....
  63. help treble
  64. audio sector- lm4780 kit
  65. This may be good for a Gainclone kit (LM3875)
  66. Will this amp need a star ground?
  67. TDA2822M amplifier circuit questions
  68. LME49720 Vs LM4562....
  69. 8 Pin DIP Socket Help Needed
  70. what capacitor type is best used on Carlosfm's non-inverting chipamp?
  71. Distortion in stereo LM3886 amp
  72. DC Servo question...
  73. where can I get some AD823 op amp?
  74. another Hum issue LM3875
  75. LM3875 powered by 28-30v wallwart?
  76. So many chip amps ?
  77. Banana's Pre - inelegant way to contrl vol
  78. swapping BA4560 in phono pre
  79. Linn Majik vs. Gainclone
  80. Noob building first amp: please check my connections
  81. pyramid PR530A/STK4192II
  82. Large Heat Sinks
  83. Is there a bridgeclone kit or PCB with integrated opamp crossover?
  84. voltages for project 88 preamp
  85. blow transformer
  86. tda2030 amp getting noise when connecting pocket tv
  87. Increase the output swing of LM3875,possible???
  88. Yamaha amp mods
  89. Help me construct my home theater
  90. Sorry to bother - 1800W for $400???
  91. Please Check this LM3886 Schematic
  92. LME49180 Based Amp Experiment
  93. First PCB Design. Any Errors?
  94. Power Supply Questions
  95. Copper source
  96. WTB: GC for Horns 109db 300hz up , some advice please
  97. max rail voltage?
  98. fan-based cooling for chipamp
  99. Bass boosted preamp, suggestions pls...
  100. Chip-Amp for Aleph P 1.7 Pre ...
  101. blown gemini mixer - need help
  102. What about NE5532?
  103. Firewire powered amplifier?
  104. Parallel LM3886, input ground, power ground, safety resistor and oscillations.
  105. I made the usb based high-end dac
  106. Trouble with my CMoy Pocket Amp
  107. BPA300 Primary Design Development
  108. My philosophy of chipamp(MUST SEE!)
  109. PGA2311 Preamp/Selector
  110. Active XO with LM3886 as opamp
  111. Adding gain to this buffer....
  112. What amp to choose
  113. RCA bypass on gainclones
  114. LM1875 design, help a newbie out
  115. Will this PCB work?
  116. PGA4311 600ohm input source impedance
  117. Inverting amp + Class A bias. is it possible or not?
  118. Mono Battery powered Amp
  119. Tube Buffered Non-Inverting Gainclone Design
  120. Chip-amp challenging D-amp ??
  121. Amplifier Performance Testing
  122. "Das Module"
  123. Heatsink approval needed for lm3886
  124. BPA200 without DC-servo
  125. New to Chip Amps
  126. Relay spark problem
  127. Case (chassis) for the amplifier
  128. Bridged lm3886 suggestions Please
  129. a study of bridge driver
  130. Non-Inverted Gainclone Clipping
  131. Shigaraki Amp thoughts
  132. Question about CT transformer and Brian's Rev C power supply board
  133. ESP P09 Question
  134. BPA PCB Layout with servo. Comments/Suggestions?
  135. ARGH! One channel failed ... where to start?
  136. Grounding of opamps. Signal or Power?
  137. Parallel LM3886 output resistor(s)
  138. My DRV134 PCB
  139. Don't Want Potentiometer in Circuit
  140. Setting up a ESP active crossover with gainclone
  141. 2 quick questions
  142. Transformer <-> Fuse size question?
  143. A rotary encoder controlled integrated chip amp LM3875
  144. How would you make this simple PCB or What?
  145. Stk412-170
  146. amplifier and screw down terminal connectors?
  147. sonic differences between inverting/non-inverting LM4780 VS both non-inverting LM4780
  148. LM3886 Pin7(gnd) current?
  149. softstart on bpa?
  150. Cmoy power supply simple question
  151. OK, This is where it hurts the most (newbie that hurt his op amp)!
  152. Questions regarding Pedra Rogics BIGC
  153. Transformer for LM3886
  154. tda 8594
  155. Speaker protection help
  156. has anyone used a Vishay-Dale vs Caddock in their chipamp?
  157. Please help about the minimum VA of transformer to drive TDA7293
  158. kem 200w (??? ) amp !!!!
  159. relay attenuators
  160. current draw of a chipamp
  161. STK4231II bridgable?
  162. cooling fan controller for chipamp
  163. Need Help With Small Stereo 4W 9V amp.
  164. LM3875 amp problem
  165. Which Dolby IC can be replaced the uA7300
  166. Guitar amp based on TDA7294
  167. Is chip amp a good CCS material?
  168. Parallelling two LM 3876 for sub
  169. new gainclone w/ reg supply (pics)
  170. Is this price True!!
  171. Favorite Threads and Posts in "Chip Amps"
  172. Using +/-70V on a LM 3886
  173. Anyone want to check my BPA schematic?
  174. 33000 uF capacitance on input of LM338 regulated supply for LM3886
  175. Regulator Chips for LM3886
  176. New preamp with LME49710
  177. Question about transformer for the TDA7294amp
  178. what is a chip amp?
  179. Max power from LM3886TF
  180. About the bridge version of the LM388
  181. dead amp
  182. BPA200 usage / bass responce
  183. fuses for tda2050
  184. 12v Chip
  185. Driver chips for BPA300 amplifier
  186. Single Sided LM3875 PCB... Crit please.
  187. chipamp.com gainclone vs audiosector.com?
  188. Which GC is good for this?
  189. LM3875 gainclone problem
  190. Transformer for LM3875
  191. stk pcboards for sale
  192. input impedance LM3875
  193. Newbie on BPA 150
  194. Another TDA2050 amp built and tested..............
  195. Noisy 3886
  196. My TDA7294 Amp
  197. My first DIY build vacuum tube style Gainclone.
  198. Direct WM8816 to differential current output DAC
  199. OPA2544 why not?, lets try!!
  200. Gaincard power connector...Please help!
  201. Lm3886 Pa200
  202. what preamp do you use with your chipamp?
  203. A bass boosted preamp or buffer advice needed
  204. Active filter plus LM3886 - one board
  205. 3way stk supply problem
  206. Working on a few amps.
  207. Calling NUUK - Diode Recommendation
  208. has anyone used a CLC + voltage regulator (like LT1083) in their project?
  209. LM3875T to be obsoleted
  210. difference between bridged and parallel?
  211. can a volume POT be used in LM4780 PCB like those from P Daniel?
  212. what resistors have you tried in your chipamp?
  213. what is the latest chipamp chip from national?
  214. LM3875 Heat Sink Issues
  215. Chipamp with SMP
  216. LVP-1's
  217. My work! LM4766 Full balanced
  218. tda 2050 - heatsinking and schem
  219. newbie pc amplifer (blown or fixable)?
  220. Suggestion for LM1875
  221. My Best DIY LM3886
  222. Different between LM3886T & LM3886TF
  223. What isolation between chips & heatsink are people using?
  224. LM3886TF-Group Buy
  225. Please explain a servo circuit
  226. help me in designing an amplifier
  227. Gainclone PCB suggestions
  228. Hot LM4702
  229. Tda7386
  230. Chipamp request for Bi-Amp with SS amp, 40+40v supply rails
  231. Web search - Waft Homehoney project made recently
  232. Hows this (toroid transformer) for a GC
  233. Building my first amp, having reservations
  234. Hook up pot help needed
  235. GC completed
  236. perceived gc phenomenon
  237. Lowest cost Chipamp, PCB+parts?
  238. DC Blocking caps on BPA200. Electrolytic?
  239. PA100 with DC SERVO?
  240. The most effective Gainclone upgrades
  241. Effect of supply bypass positioning.
  242. 200w Tda2030 Amp - Need Help !
  243. Various questions from a diy noob regarding the myrefC.
  244. Tube buffered, IGC mod.
  245. [help] pimeta ground buffer heating up
  246. preamp / source / output selector
  247. 5 channel transformer rating for LM4780/LM4781
  248. Help!Building first amp......
  249. Cambridge Audio A1 Gainclone Conversion
  250. LME49810 - a new cousin for LM4702

Content Relevant URLs by vBSEO 3.3.2