Corian Turntable Fun - Page 40 - diyAudio
Go Back   Home > Forums > Source & Line > Analogue Source

Analogue Source Turntables, Tonearms, Cartridges, Phono Stages, Tuners, Tape Recorders, etc.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 24th March 2007, 10:05 AM   #391
owen is offline owen  United Kingdom
diyAudio Member
 
Join Date: Mar 2004
Location: Shilton
Casey,

You know where I am... sadly being 1000's of miles away, I cant offer the help of a soldering iron, or a six pack, to inspire the project onwards


Talk to you soon


Owen
  Reply With Quote
Old 24th March 2007, 01:07 PM   #392
...truth seeker...
diyAudio Member
 
Ed LaFontaine's Avatar
 
Join Date: Feb 2004
Location: where the Appalachians rise from the Blue Grass
Casey,
My heart goes out to all of you invloved in the process.
  Reply With Quote
Old 11th October 2007, 07:10 PM   #393
diyAudio Member
 
mavallarino's Avatar
 
Join Date: Oct 2006
Hello to all and above all Casey,

I only read this thread now for the first time.

I think we all will need to wait for the bearing/motor group buy. Casey when you settle everything you will have a paying customer (discounts for pre-donators?)!!! It must be soon because I would like to do a similar project in December.

In boca al lupo (good luck in italian jargon),

M
  Reply With Quote
Old 3rd November 2007, 06:57 PM   #394
Account Disabled
 
Join Date: Sep 2004
Location: Earth
Casey, great work. I'm really impressed!
Can't wait to see the complete project!
  Reply With Quote
Old 19th May 2009, 01:06 AM   #395
diyAudio Member
 
Join Date: Aug 2008
Hi Casey,
Hope everything's fine over there. Just read this thread and I think you've done a wonderful job so far. Good luck on completing this, I'm sure it would be worth it.

Cheers!
  Reply With Quote
Old 9th July 2009, 04:07 AM   #396
YohY is offline YohY  United Kingdom
diyAudio Member
 
Join Date: Jul 2009
Location: Cardiff, UK
Default Settled dust ?

My my...I just wandered back onto DIYaudio... I remembered following a great turntable build which was based on using Corian acrylic sometime back - Todays date is July 9th 2009.

There's a block of multi-layered Corian that resembles a TT gathering dust somewhere



I guess the dust did settle after all...(!)


I trust you are well Casey ! -Andy-
  Reply With Quote
Old 15th November 2009, 02:14 AM   #397
mrevie is offline mrevie  Australia
diyAudio Member
 
Join Date: Jan 2009
Just read through this entire thread. What an amazing process!

I hope everything is well with you Casey!

Steve.
  Reply With Quote
Old 15th November 2009, 02:28 AM   #398
Banned
 
Join Date: Nov 2005
Location: McKinney, TX
Been thru it before. Never easy, even if you are the one that wants it. Life goes on, but slowly at first. Wake up each day, pray for the knowledge to do the right thing for that day and hope that it will be a good day.
Best of luck on your new life. I kind of know a little bit of what you must be going thru right now.
  Reply With Quote
Old 11th November 2013, 10:09 PM   #399
diyAudio Member
 
Join Date: Dec 2006
What happened to valveitude and the Corian turntable?
  Reply With Quote
Old 8th June 2014, 04:38 AM   #400
diyAudio Member
 
Join Date: Jan 2009
Default spring coupler for AC line direct drive sync' motor?

Quote:
Originally Posted by valveitude View Post
Turntable:.... Since my first attempt to address it's [ spring coupler] problems by wrapping it in a rubber blanket didn't work out, I came up with another approach...

Click the image to open in full size.

RTV silicon glue. I applied it in three steps. First I compressed it so the coils touched, and laid down about a 1/16 of an inch. When I let it expand, it pulled the silicon in between the coils. I let it sit over night, and when it had cured, laid down another 1/16”. Finally, after it cured again, I filled in any voids, and ran a fillet on the ends. The entire process was done with a 1/8” shaft of a Dremel tool inserted to insure a perfect alignment as the rubber cured. How does it work? Oh...My...God. Not only does the silicon damp the spring resonance, but apparently it helps kill the motor noise at the source. So much so that I can no longer hear any motor hum while it's hanging on the “kinda horn” noise amplifier outside the housing! You can believe I'm grinning like a Cheshire cat now. Whistlin' while I worked, I reassembled the motor, and set it up on table. Fluorescents off, screwdriver pushed in my ear, I went hunting for noise. Side of motor housing..nothing. Top plinth..nothing. Bottom plinth..nothing . The only mechanical noise I could find was on the motor's top plate. The side load on the bushing from the belt increased the top bushing noise from zero to something slightly greater than zero. The top plate acts like a sounding board for any noise the bushing makes. I had actually anticipated this from the beginning..why I cut a recess in the top for a Sorbothane donut. I'm sure once this is in place, this minuscule noise will be gone as well. As for airborne noise at the belt, all but disappeared. There is no longer any belt vibration that I can feel, and the noise level has dropped to the point that all you hear, with your ear practically touching the pulley, is a combination of belt hiss, mixed with a faint bushing noise, and a random static crackle (the hiss may be static as well)...Casey
Question for C or other interested parties: Could Casey's revised spring coupler be used effectively for a direct drive 33-1/3 rpm AC motor to turn a turntable platter?
...regards, Michael
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Corian for tube amp? Sherman Tubes / Valves 2 29th September 2004 11:55 PM
WTB Corian CV Swap Meet 4 27th September 2003 02:15 PM


New To Site? Need Help?

All times are GMT. The time now is 02:12 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2