
Home  Forums  Rules  Articles  diyAudio Store  Blogs  Gallery  Wiki  Register  Donations  FAQ  Calendar  Search  Today's Posts  Mark Forums Read  Search 
Analogue Source Turntables, Tonearms, Cartridges, Phono Stages, Tuners, Tape Recorders, etc. 

Please consider donating to help us continue to serve you.
Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving 

Thread Tools  Search this Thread 
17th March 2013, 07:37 PM  #21 
diyAudio Member
Join Date: Mar 2009

Yes, the curves bottom out on the right side.
At least at lower impedances. I was talking about ultra low Rbb transistors. They really need some current to show improvements over higher Rbb ones. I found many MC heads where idle was just too low. It makes of cause so sense to run the input stage on high current when you have a cartridge like the DL103 with 40 Ohm DC impedance. 
17th March 2013, 07:42 PM  #22 
diyAudio Member
Join Date: Jul 2004
Location: Scottish Borders

I thought it was common knowledge that low noise amps ran at high bias currents. Even jFET input seem to benefit from high bias currents for lowest noise.
__________________
regards Andrew T. 
17th March 2013, 07:49 PM  #23 
diyAudio Member
Join Date: Mar 2009

The question is : what is high bias current ?
Some think that 1mA is already high. Some examples are the LindsleyHood designs and early Self. In the latest version of his preamp ( Elektor ) he has ramped it up a bit for a total of 4mA though. I think that is still too low when you have one of the very low impedances cartridges that come out now, say from Lyra ( Atlas, 4 Ohm ) or My Sonic Lab ( 2 Ohm and less ). Modern neodym magnets make that possible. The Atlas for example gives out nearly 1mV at 5cm/sec. That is of cause a fantastic combination for high S/N. It would be a pity when the MC head destroys this. 
17th March 2013, 07:52 PM  #24 
diyAudio Member
Join Date: Jul 2004
Location: Scottish Borders

5mA per half of the LTP would be high for me.
That is 10mA of tail current compared to 1/4mA, or 1mA, for a higher noise LTP.
__________________
regards Andrew T. 
17th March 2013, 08:00 PM  #25 
diyAudio Member
Join Date: Mar 2009

Here are Syn08īs noise calculations. When you go over it you find enormous bias when Rbb is ultra low. He runs his 0.3nV/qHz bipolar head on 28mA.
I battled with him for month but in the end i gave in. Of cause distortion has to be considered too, especially in an open loop design. Taking this into account i found the optimum at 5 to 10mA per transistor. That works only when the PNP has a high early voltage. For a transistor like the BC327 with Rbb of ca.30 Ohm it comes out at 2.5mA. More then that and the early effect comes into play quite drastic. 
17th March 2013, 08:02 PM  #26 
diyAudio Member
Join Date: Mar 2009

Here is the text....

18th March 2013, 05:56 PM  #27 
diyAudio Member


18th March 2013, 07:07 PM  #28 
diyAudio Member
Join Date: Sep 2004
Location: virginia

I looked in my book, Low Noise Electronic Design, and found the formula for transistor voltage noise.
En=4ktRbb+2qIcRe**2 Re**2 means Re squared. The first term is the thermal noise in the base spreading resistance and the second term is the noise in the Shockley emitter resistance, given below. Re=kt/(qIc)=1/Gm You can't change the first term but the second term can be reduced by increasing the collector current, Ic. You can decrease the second term to much less than the first term so base spreading resistance noise dominates. 4ktRbb>>2qIcRe**2 If I did the algebra correctly you obtain this. Ic>>0.026/(2Rbb) or approximately Ic>>1/(80Rbb) 
18th March 2013, 07:18 PM  #29 
diyAudio Member
Join Date: Mar 2009

Fits approximately to my 5 to 10mA with low Rbb transistors.
1/ 80 x 2 = 6.25mA 
18th March 2013, 07:56 PM  #30 
diyAudio Member

The red line is SQRT current noise, the green is SQRT thermal noise and the blue is SQRT kernel noise. The violet line is the net. I used the same formulas. In this example, once the kernel noise is 30% below the thermal noise there would appear to be little benefit to increasing Ic.

Thread Tools  Search this Thread 


Similar Threads  
Thread  Thread Starter  Forum  Replies  Last Post 
"...the best preamplifier ever made" says Mr. David Price, HiFi World  tiefbassuebertr  Analog Line Level  73  21st May 2017 04:51 PM 
John Curl Mc Kinnie phono prepreamplifier  Antoni Rende  Solid State  14  14th January 2017 09:27 AM 
Musical Surroundings MM/MC Phonomena Phono Preamplifier  kp93300  Analogue Source  0  11th October 2009 01:15 PM 
HQ Balanced Phono Preamplifier for MC Cartridges using OPA2604  BiepBiep  Analog Line Level  5  1st November 2008 05:27 AM 
New To Site?  Need Help? 