My version of an Ultrasonic Record Cleaner - Page 67 - diyAudio
Go Back   Home > Forums > Source & Line > Analogue Source
Home Forums Rules Articles diyAudio Store Gallery Wiki Blogs Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Analogue Source Turntables, Tonearms, Cartridges, Phono Stages, Tuners, Tape Recorders, etc.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 18th June 2014, 07:47 AM   #661
Zg925 is offline Zg925  United States
diyAudio Member
 
Join Date: Feb 2014
Location: Woodland Hills, Ca.
Default new USA US cleaner

Hey folks, I found a new USA US cleaner company. I was trying to repair a Sonix 4 cleaner. The proprietary T03 power transistor is unavailable from them however you can buy a new power board for $180. Forget that! So I thought maybe someone makes a 60 KHZ power board and came across this site. Vibrato Ultrasonic Equipment Needles to say I was pretty excited about what they are doing and for those DIY's there is a bare board you can buy amongst the US cleaners they sell. I used to do electronics and their design is miles above what is currently being sold.

I contacted them and the owner, Louis Steele, replied. They are a small company just incorporated this past January. He used to work for one of the US companies mentioned in this thread. I asked about 60 KHZ and his reply.

Quote:
I can produce a special order Vibrato Ultrasonic Cleaner as follows: 6 Quart tank with 4 - 60khz Transducers (35 watts each for a total of 140watts), and the Digital Heater with Countdown Timer Control (user configurable heat and time) for a cost of $385.45 and $8.75 shipping in the United States.
For the same unit with the Fixed Heater and Timer Controller the cost would be $375.68 plus $8.75 shipping in the United States. (the fixed heater can not be changed, however, I can adjust the timer).
My ultimate goal is to allow customers to select the options that they need, such as your request, by choosing the frequency, tank size, type of timer, frequency sweep, and heat/no heat, etc.
Any rate check them out and see what you think. As soon as I get enough coin I will be ordering one of their units.

Final note, I pointed Louis to this thread so he is aware of the discussion on the good and bad about the US cleaners available.
  Reply With Quote
Old 18th June 2014, 01:44 PM   #662
ebuzz is offline ebuzz  United States
diyAudio Member
 
Join Date: Jan 2009
Location: NY
Quote:
Originally Posted by Zg925 View Post
Hey folks, I found a new USA US cleaner company. I was trying to repair a Sonix 4 cleaner. The proprietary T03 power transistor is unavailable from them however you can buy a new power board for $180. Forget that! So I thought maybe someone makes a 60 KHZ power board and came across this site. Vibrato Ultrasonic Equipment Needles to say I was pretty excited about what they are doing and for those DIY's there is a bare board you can buy amongst the US cleaners they sell. I used to do electronics and their design is miles above what is currently being sold.

I contacted them and the owner, Louis Steele, replied. They are a small company just incorporated this past January. He used to work for one of the US companies mentioned in this thread. I asked about 60 KHZ and his reply.

Any rate check them out and see what you think. As soon as I get enough coin I will be ordering one of their units.

Final note, I pointed Louis to this thread so he is aware of the discussion on the good and bad about the US cleaners available.
Interesting! I might be up for one of these myself. It's much cheaper that some of the other units. I guess the question is reliability. Is there a pix?
  Reply With Quote
Old 18th June 2014, 03:17 PM   #663
Zg925 is offline Zg925  United States
diyAudio Member
 
Join Date: Feb 2014
Location: Woodland Hills, Ca.
Just click on the highlited link Vibrato Ultrasonic Equipment in my original post.
  Reply With Quote
Old 18th June 2014, 03:46 PM   #664
ebuzz is offline ebuzz  United States
diyAudio Member
 
Join Date: Jan 2009
Location: NY
Quote:
Originally Posted by Zg925 View Post
Just click on the highlited link Vibrato Ultrasonic Equipment in my original post.
Got it. Looks kinda shabby, however. Plastic isn't as nice as the metal ones. Oh well, need to think on it.
thanks
  Reply With Quote
Old 18th June 2014, 10:25 PM   #665
Zg925 is offline Zg925  United States
diyAudio Member
 
Join Date: Feb 2014
Location: Woodland Hills, Ca.
Quote:
Originally Posted by ebuzz View Post
Got it. Looks kinda shabby, however. Plastic isn't as nice as the metal ones. Oh well, need to think on it.
thanks
I look at it a little differently. You could take the unit and put it in you own custom setup like a recess mount instead of having to dissect it from a metal enclosure. Of course the plastic isn't the best but I'm looking at the cleaner and not the enclosure. Besides it looks like they are big on guaranting theirvcleaners.
  Reply With Quote
Old 19th June 2014, 07:33 AM   #666
diyAudio Member
 
Join Date: Apr 2004
Location: Maine
Send a message via AIM to Doctorcilantro Send a message via MSN to Doctorcilantro Send a message via Yahoo to Doctorcilantro
It is metal housed in plastic. Shipping costs are lower, and I don't think there would be any detriment to housing the metal trough in the plastic...
  Reply With Quote
Old 19th June 2014, 03:02 PM   #667
ebuzz is offline ebuzz  United States
diyAudio Member
 
Join Date: Jan 2009
Location: NY
Quote:
Originally Posted by Zg925 View Post
I look at it a little differently. You could take the unit and put it in you own custom setup like a recess mount instead of having to dissect it from a metal enclosure. Of course the plastic isn't the best but I'm looking at the cleaner and not the enclosure. Besides it looks like they are big on guaranting theirvcleaners.
Don't be confused by the fact that I'm a member of this forum and assume that I know anything about the art of DIY! I'm scared to try this project even after all the help and reading all the posts in this thread, and I have read them all --- twice!
  Reply With Quote
Old 19th June 2014, 09:23 PM   #668
CT0wens is offline CT0wens  United States
diyAudio Member
 
CT0wens's Avatar
 
Join Date: Jun 2012
Default You have my business

Louis - Thank you for this and your quick reply e-mails last night. I've joined the Tindie wait list. Looking forward to swapping out my cheap 40khz fleabay unit.

cheers - Christopher
  Reply With Quote
Old 19th June 2014, 10:54 PM   #669
diyAudio Member
 
Kindhornman's Avatar
 
Join Date: Aug 2012
Location: Los Angeles, California
I pop in here once in awhile to see what is up and who has built what. I see the Vibrato units and though the plastic enclosure, looks like a plastic storage container looks kind of cheap, come on this is a diy site isn't it. How hard would it be to make a nice enclosure for the unit, it sure seems fairly simple. I have seen some of the units built here and I must say I wouldn't want to actually have to look at any of them, they are monstrosities sitting in a nice room. I would want to build it into something so only the upper mechanism for holding the records would show, and definitely not the pump and hoses and things. Anyone with a wife or girlfriend is going to hear S**t about how these things would look in a room. A stainless tub flush mounted in something nice would be something else. Anyway just my opinion and I do industrial design so shoot me if you want. Thanks for keeping the thread going it has been educational.

Last edited by Kindhornman; 19th June 2014 at 10:57 PM.
  Reply With Quote
Old 20th June 2014, 01:49 AM   #670
CT0wens is offline CT0wens  United States
diyAudio Member
 
CT0wens's Avatar
 
Join Date: Jun 2012
Here, Here. “Life is trying things to see if they work.” – Ray Bradbury
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
I made myself a record cleaner Sclalars Analogue Source 231 20th February 2017 05:01 PM
My DIY record cleaner. mattjk Analogue Source 105 9th March 2016 04:05 AM
Ultrasonic Record Cleaner- any feedback Ianmac Analogue Source 7 13th November 2012 03:28 AM
diy ultrasonic cleaner, not using bought unit 3GGG Analogue Source 0 10th January 2011 09:28 AM
Ultrasonic Parts cleaner... DIY??? pk386 Everything Else 1 10th May 2004 06:55 PM


New To Site? Need Help?

All times are GMT. The time now is 06:25 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio

Content Relevant URLs by vBSEO 3.3.2
Wiki