DIY MICRO SEIKI RX 5000 TURNTABLE - Page 2

regular · 31st December 2011, 12:36 AM

Quote:

Originally Posted by Holger Barske

BTW.: Bulit something a little alike this a few years ago:

Nice. looked very impressive. Platter by your self?

Holger Barske · 31st December 2011, 01:03 AM

No. This is an 80 mm acrylic platter from Scheu Analog, the bearing is also from there. Motor and belt are from TW Acustic, chassis is slate, all metal parts are stainless steel.
Still using it from time to time, not a bad turntable.

limono · 31st December 2011, 01:51 AM

Holger
Really nice table and classically German meaning quadratisch, praktish, gut

are those belts still available from TW Acoustic? I don't see anything on their website.

Stuartarm · 2nd January 2012, 02:28 AM

Quote:

Originally Posted by Holger Barske

BTW.: Bulit something a little alike this a few years ago:

nice work Holger...I was thinking of using a ms arm board in my current tt project as it is still readily available...they are plenty beefy and reasonably priced for what it is...clear audio has a nice board as well but the machined aluminum for the solution is expensive...there is a Chinese version on ebay for much less?...I have not yet chosen an arm so the decision is still up in the air as to hole size etc?...if you have any suggestions as to an arm board on a three point plinth like the clear audio solution I would appreciate it...thanks

Armalex · 28th January 2012, 08:24 AM

Dear Regular,
I liked what you did it's very nice. I myself am planning to build something similar. Would you please supply additional info regarding Bearing?
Best regards,
Armen

Armalex · 2nd February 2012, 07:20 AM

Quote:

Originally Posted by regular

Hi All,
This is A turntable is made by our group.
The next few days I will set up a sturdier shelves

Dear Regular,
Nice job! Would you please give me more info regarding Bearing?
Best Regards,
Armen

regular · 23rd April 2012, 02:31 AM

Quote:

Originally Posted by Armalex

Dear Regular,
Nice job! Would you please give me more info regarding Bearing?
Best Regards,
Armen

I'm sorry because to lated reply

I wish you success

Best Regards,

regular · 23rd April 2012, 03:07 AM

Bearing image

31st December 2011, 01:03 AM	#12
Holger Barske diyAudio Member Join Date: Jan 2001 Location: Ruhrgebiet	No. This is an 80 mm acrylic platter from Scheu Analog, the bearing is also from there. Motor and belt are from TW Acustic, chassis is slate, all metal parts are stainless steel. Still using it from time to time, not a bad turntable. __________________ Best regards: Holger www.holgerbarske.com

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Micro Seiki Tonearm.	MiiB	Analogue Source	2	28th May 2007 03:14 PM
Micro Seiki BL 99V - turntable Power Supply	CHEVALLIER	Analogue Source	7	13th March 2007 07:19 PM
Vacuum pump for Micro Seiki turntable	jam	Analogue Source	4	16th October 2004 10:18 PM
Micro Seiki 1500	Cobra2	Analogue Source	18	15th November 2003 09:33 PM
Micro Seiki MC	ktigerb	Analogue Source	0	27th May 2003 09:16 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

31st December 2011, 01:51 AM	#13
limono diyAudio Member Join Date: Mar 2007	Holger Really nice table and classically German meaning quadratisch, praktish, gut are those belts still available from TW Acoustic? I don't see anything on their website.

28th January 2012, 08:24 AM	#15
Armalex diyAudio Member Join Date: Jan 2012	Dear Regular, I liked what you did it's very nice. I myself am planning to build something similar. Would you please supply additional info regarding Bearing? Best regards, Armen

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)