Help, I need a combined head for ReVox B215! - diyAudio
Go Back   Home > Forums > Source & Line > Analogue Source

Analogue Source Turntables, Tonearms, Cartridges, Phono Stages, Tuners, Tape Recorders, etc.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 9th March 2008, 12:04 AM   #1
diyAudio Member
 
Join Date: Nov 2007
Default Help, I need a combined head for ReVox B215!

Does somebody know where I could get used but in good condition or a new playback/record head for deck ReVox B215? It has a very pretty mechanism - I hate to see it staying in my closet because the head is completely worn out.

Thanks a lot,
Dimitar
  Reply With Quote
Old 15th March 2008, 04:30 AM   #2
diyAudio Member
 
Join Date: Mar 2008
Default Revox Head

There is a person who bought out Nortronics, the OEM manufacturer of Reel to Reel recorders. He has a head match, perhaps not OEM but superior to OEM.
Have you relaped your heads yet. If not you may want to do this first; and then purchase a new set.
In addition you need to find someone who knows how to bias the recorder for maximum tape saturation. Most biasing is designed for MOL or maximum operating level, generally plus 6 db or 516 nwbr, with a controlled frequency response of 50 to 11.5 KHZ at -1db. This is done by increasing the bias voltage at 11.5KHZ, ref. 100KHZ at 7.5 inches per second and monitoring the play back head to where the meter goes past the 6 db range and overbiases dropping to 5 db using a signal generator and a volt meter. 3 db doubles the voltage, so 6 db would be a reference of 4 volts out. So doing this little trick, your machine will work 1 db hot. For 15 inches per second, your machine more than likely would need instead of 100 KHZ, a doubling of the bias. Just remember that bias effects frequency response, more bias less distortion however; and thats why Revox/Studder uses the theory of MOL, maximum operating level.
Please keep in mind this is to cause roll off at that set frequency, allowing for maximum out put. After all a good 4 volts out makes nuiances in digital rather wimpish; and the analogue attack and decay constants of analog are about 100 times faster in real time.
Hope, I have been of help. If you need the name of the Nortronics new named supplier, please e-mail me in kind.
Finally, keep in mind the laws of Physics, frequency response above the music spectrum is dangerous and adds alot of noise to your recording. Remember 1st harmonic 4.4 KHZ, 2nd Harmonic 8.8 KHZ and third harmonic 12.6KHZ - all the sound you would ever need; and only 3% of the 3rd harmonic is required.
Compare this to digital 4.4 medium, intermodulating with the 44.4 KHZ pilot frequency with a controlled bandwith of 10KHZ; and the fact that digital is a beat frequency/psycho accoustic fraud meaning that you hear the harmonics in reverse order, like hearing the bullet flying by before you hear the blasting cap leaves little wonder why bass can be heard predominately with digital. The threshold presence to distortion leavel of digial to me is pathetic - and digital audiophiles do not even hear the reference threshold, which makes the actual usuable db range of digital to about 10 dbs as compared to your revox at 60 dbs, not to mention equilization speed, 60 microseconds of digitals best compared to 5 microseconds of a high end 7.5 inch per second reel to reel.
leelandwhite2001@yahoo.com
  Reply With Quote
Old 15th March 2008, 03:29 PM   #3
oshifis is offline oshifis  Hungary
diyAudio Member
 
Join Date: Mar 2004
Location: Budapest, Hungary
This is a cassette recorder, not R2R. Most heads can be safely replaced by other OEM heads of same DC resistance. Recalibration will be necessary, of course.
  Reply With Quote
Old 15th March 2008, 04:27 PM   #4
diyAudio Member
 
Join Date: Nov 2007
Default combined head for cassette deck ReVox B215

Thank you for the replies. I have heard for instance that the combined head of cassette decks Sony TC-K71 and Sony TC-K81 is identical to that of ReVox B215. So bought old Sony TC-K71 from ebay and will be replacing the worn-out headset with its own. Have somebody done something similar ? Are there any tricky moments? For instance I saw that the ReVox headset is inside a casing which is different that the Sony headset casing. So for now the only tricky moment which I see is to get the old headset from its casing and put the new one there.

Dimitar
Attached Images
File Type: jpg pic8.jpg (28.1 KB, 96 views)
  Reply With Quote
Old 16th March 2008, 08:53 PM   #5
Ghianni is offline Ghianni  Greece
diyAudio Member
 
Join Date: Sep 2005
Go here :ftp://ftp.studer.ch/Public/Products/Revox/Revox_B215/
and download the SM then find the part number of the replay/rec head block it is from Cannon. May be Studer has it in stock. From the pic I see you need also the two rollers...
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Revox B215 for parts. cinematographer Parts 4 5th January 2009 03:52 PM
Question about cassette deck Revox B215 Dimitar13 Analogue Source 1 4th April 2008 09:26 PM
PL-41 and MMF2 combined? pjanda1 Analogue Source 0 28th January 2007 03:41 PM
motor types head to head for a TT p_ete2003 Analogue Source 20 11th January 2007 08:29 PM


New To Site? Need Help?

All times are GMT. The time now is 11:56 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2