
Home  Forums  Rules  Articles  diyAudio Store  Blogs  Gallery  Wiki  Register  Donations  FAQ  Calendar  Search  Today's Posts  Mark Forums Read  Search 
Analog Line Level Preamplifiers , Passive Preamps, Crossovers, etc. 

Please consider donating to help us continue to serve you.
Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving 

Thread Tools  Search this Thread 
22nd May 2015, 12:13 AM  #1 
diyAudio Member
Join Date: Jan 2015

Not Equal Slope of Active Crossover at Same Cut Of Frequency
Hi! I am a new member.
Recently tring to build a 2nd order active crossover circuit using fieild standard structure,ie,2 identical resistor and 2 identical capacitor and 2 opamp( one input unity buffer , one for filter). As completed the assembly,I tested the circuit function with sinwave generator and digital oscillscope than found: 1.output voltage changes about 0.5v as frequency changes about 1.5k hz for low pass structure,but 2.output voltage changes about 0.5v as frequency changes about 5k hz for high pass structure. theoretically, increasing and decreasing slop shall be indentical for high and low pass,is it? Why I got different slop? Will appreciate any one can reply the answer. 
22nd May 2015, 01:55 AM  #2 
diyAudio Member
Join Date: Apr 2011


22nd May 2015, 04:39 AM  #3  
diyAudio Member
Join Date: Jan 2015

Not identical slop
Quote:
Circuit as attached file, slop is indeed different. 

22nd May 2015, 05:44 AM  #4 
diyAudio Member
Join Date: May 2008
Location: Croatia

maybe you need another buffer after filter?

22nd May 2015, 06:04 AM  #5 
diyAudio Member
Join Date: Sep 2004
Location: Minneapolis, Minnesota, USA

First of all, for your Fc calculation you have an extra term that does not apply here; drop the X 1.414 factor, that only applies to a LR4 alignment not a B2 as you show. With the values used you get a B2 @ 6.8kHz.
If you are getting anything else you must have a bad component or a wiring/connection error. Schematic.JPG Slpoes.jpg Mike 
22nd May 2015, 08:11 AM  #6 
diyAudio Member
Join Date: Jul 2004
Location: Scottish Borders

The Butterworth rolloff curve can be approximated to a theoretical two line "curve".
The horizontal line in the passband and the slope line in the stopband. The 2pole filter has a slope of 12dB/octave, which is equal to 40dB per decade. The intersection of these two lines is calculated using the F3dB formula. The actual response at the F3dB frequency is 3dB down from the theoretical intersection point. Either side of that "point" the actual response lines get closer to the theoretical lines, but they take a lot of octaves before they get close enough to be immeasurably equal to the theoretical. You should take account of this difference between the 2slope and the curve of the Butterworth response. You can see the actual curve in Michael's example. The F3dB is @ ~6.8kHz. You can see the curve has not reached the straight line part at 3.4kHz and at 13kHz. But it is getting very close. You can measure out at one decade (~3 octaves) from 6.8kHz and measure the difference @ 680Hz and @ 68kHz and your difference will still exceed 1% (~0.1dB).
__________________
regards Andrew T. Last edited by AndrewT; 22nd May 2015 at 08:16 AM. 
23rd May 2015, 02:29 PM  #7 
diyAudio Member
Join Date: Jan 2015

Not Equal Slope of Active Crossover at Same Cut Of Frequency
After closely review Andrew's and Micheal's messages,I probably know the cause of my question.
According to the frequency response graph(Take Micheal's graph as example),the XAxis scale is not identical with increasing frequency.For high pass filter,output increasing from 35db to 3db(Around 7k hz point) as frequency increased from 1khz to 7 khz,ie,output is 32db increased with 6khz increment. For low pass filter,also 32db output decreased with 33khz increment(From 7khz to 40khz). So that the both slope is identical. Question:If Imake the graph with same scale freqnency increment(every 100hz or 200hz......),the up/down slope is still not indentical,my question is still there. 
23rd May 2015, 04:32 PM  #8 
diyAudio Member
Join Date: Sep 2004
Location: Minneapolis, Minnesota, USA

Maybe this will help. A second order filter roll off slope is 12dB per octave or 40dB per decade. Decibels use a logarithmic scale. To illustrate this in a way that is easier to see, I've recalculated the HP and LP filters for a 1kHz Fc.
Schematic.JPG Slpoes.jpg Mike 
23rd May 2015, 07:23 PM  #9  
diyAudio Member
Join Date: Jul 2004
Location: Scottish Borders

Quote:
If the filter is single pole then you will see a slope of 6dB/octave. One octave is a doubling or halving of the frequency. i.e a change of 6dB when the frequency changes by half. A Butterworth 2pole (sometimes written as B2) would be a change of 12dB for a doubling or halving of frequency. You can see this in Michael's latest plot. 40dB@ 100Hz, 12dB higher @ 200Hz (28dB), 24dB higher at 400Hz (16dB) here you can see the difference from the theoretical straight line and the actual, 36dB higher @ 800Hz (4dB) now the difference really shows up. 40dB higher @1kHz (0dB) now the difference is 3dB. i.e. difference between the Theoretical and the actual at the rolloff frequency has become 3dB.
__________________
regards Andrew T. Last edited by AndrewT; 23rd May 2015 at 07:32 PM. 

24th May 2015, 04:17 AM  #10  
diyAudio Member
Join Date: Jan 2015

Quote:
Refer to your graph(Ft 1khz),high pass slope frequency changes from 100hz to 1k hz and resulting 40db changes.The low pass slope frequency,howerever,changed from 1k hz to 10 khz and resulting same 40 db changes,both slopes is identical because of same decade. Question1:For hp 1khz change can results 40db changes,but for lp needs 10k hz. so actually the slope is indeed not identical if graph is made with same scale for Xaxis,ie,100 hz to 1k hz for hp and 1k hz to 1.9 K HZ for lp, is it correct? Question2:The Fc equation can result many combination of R and C,what will be different by using different R and C? Thank you very much/jsc 

Thread Tools  Search this Thread 


Similar Threads  
Thread  Thread Starter  Forum  Replies  Last Post 
NOT EQUAL SLOP OF ACTIVE CROSSOVER AT SAME CUT OFF FREQUENCY  jsc5925161  Introductions  1  21st May 2015 03:04 PM 
Active Crossover Design: How the drivers influence filter type/topology/slope?  Chris Blanchard  Analog Line Level  16  14th December 2014 07:24 PM 
Advice on crossover frequency and slope  spot  Subwoofers  5  5th October 2011 04:14 AM 
Any discrete active crossover with 48db slope?  asturias  MultiWay  3  20th April 2010 04:58 PM 
Active crossover dirty slope  argonrepublic  Parts  6  11th July 2005 04:26 AM 
New To Site?  Need Help? 