Broskie

kingfisher · 11th May 2012, 02:17 PM

Can someone tell me how I purchase products at the TubeCAD yahoo store?
I have been trying to get their online parts selector to work, but all I get is an option to add a selector switch! I wish to purchase a board and populate it with all the necessities! I have a case and dials so far!
Any help would be greatly appreciated!
Francis

wirewiggler · 11th May 2012, 02:22 PM

He may be out of stock,Items out of stock the purchase button is gone. If you do get it to work don't be freaked out if a takes a while for him to ship i think he waits until he has few orders before he ships.

Bill

kevinh · 11th May 2012, 02:29 PM

You might want to go to his blog, Tube CAD Journal , he mentioned waiting for pcb's to arrive. He is ading new PCB's not sure if he is 'replacing' some less integrated boards.

kingfisher · 11th May 2012, 02:45 PM

Browsing the yahoo store I find much of this over my head, but I had built the GG Pre-Amp kit in the past, but I am a novice at best, is there help in assembling a kit? I have other questions also, but would like to get started with (PURCHASING) and assembling the Unbanlancer as line-amp. In your opinion if a novice like myself wanted to build his own line amplifier which type/circuit would be a good choice?
Francis

wirewiggler · 11th May 2012, 03:21 PM

I just purchased the Octal board, this will be my fifth or sixth tube project and this one will be a little more challenging . While John offers a excellent product he does not offer much hand holding in the support end. He assumes you ether have tube building knowledge or are willing to research the info you need. I have been reading his Tube cad journal and have to admit it is bit over my head and plan to pick up some more reading material. I think Morgan Jones new book may be in order.

Bill

kingfisher · 11th May 2012, 03:32 PM

I have the following tubes now: pr. 6GM8/ECC86, pr.12AU7/ECC82, 4pr.12AT7WC
I would like to build without buying more tubes, so the choices are there! I would like to build a Low Voltage line amp also, but need to pair the 6GM8 with another suitable tube...
Any thoughts on this?

kingfisher · 11th May 2012, 03:56 PM

Most of my problem stems from getting the purchase completed! I know this is a odd question, but how did you go about buying the board?

wirewiggler · 11th May 2012, 09:59 PM

Are you on the glassware site?
GlassWare Audio Design Software

Bill

tinitus · 11th May 2012, 10:54 PM

bias resistors are certainly not missing
plenty of those(attached picture)
you only need to figure out which one

manual seems quite comprehensive, and detailed
but ofcourse, all still nonsense if you have no clew how a tube amp works
been looking at my kit for about a week now, and beginning to understand it

edit, and using non listed tubes ofcourse doesnt make it any easier

11th May 2012, 02:17 PM	#1
kingfisher diyAudio Member Join Date: Feb 2010 Location: Eastern Ontario CA.	Broskie Can someone tell me how I purchase products at the TubeCAD yahoo store? I have been trying to get their online parts selector to work, but all I get is an option to add a selector switch! I wish to purchase a board and populate it with all the necessities! I have a case and dials so far! Any help would be greatly appreciated! Francis

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
John Broskie MIA?	MrBurd	Tubes / Valves	11	6th July 2011 05:14 PM
Broskie tda1543	vita	Digital Line Level	0	21st September 2009 03:28 PM
Broskie OTL	woody	Tubes / Valves	1	18th October 2007 05:18 AM
broskie voltage regulator	dave dove	Tubes / Valves	2	14th January 2007 09:50 PM
Where is John Broskie ?	reinhard	Tubes / Valves	7	8th October 2002 01:27 PM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

11th May 2012, 02:22 PM	#2
wirewiggler diyAudio Member Join Date: Mar 2005 Location: Bakersfield Ca	He may be out of stock,Items out of stock the purchase button is gone. If you do get it to work don't be freaked out if a takes a while for him to ship i think he waits until he has few orders before he ships. Bill

11th May 2012, 02:29 PM	#3
kevinh diyAudio Member Join Date: May 2007	You might want to go to his blog, Tube CAD Journal , he mentioned waiting for pcb's to arrive. He is ading new PCB's not sure if he is 'replacing' some less integrated boards.

11th May 2012, 02:45 PM	#4
kingfisher diyAudio Member Join Date: Feb 2010 Location: Eastern Ontario CA.	Browsing the yahoo store I find much of this over my head, but I had built the GG Pre-Amp kit in the past, but I am a novice at best, is there help in assembling a kit? I have other questions also, but would like to get started with (PURCHASING) and assembling the Unbanlancer as line-amp. In your opinion if a novice like myself wanted to build his own line amplifier which type/circuit would be a good choice? Francis

11th May 2012, 03:21 PM	#5
wirewiggler diyAudio Member Join Date: Mar 2005 Location: Bakersfield Ca	I just purchased the Octal board, this will be my fifth or sixth tube project and this one will be a little more challenging . While John offers a excellent product he does not offer much hand holding in the support end. He assumes you ether have tube building knowledge or are willing to research the info you need. I have been reading his Tube cad journal and have to admit it is bit over my head and plan to pick up some more reading material. I think Morgan Jones new book may be in order. Bill

11th May 2012, 03:32 PM	#6
kingfisher diyAudio Member Join Date: Feb 2010 Location: Eastern Ontario CA.	I have the following tubes now: pr. 6GM8/ECC86, pr.12AU7/ECC82, 4pr.12AT7WC I would like to build without buying more tubes, so the choices are there! I would like to build a Low Voltage line amp also, but need to pair the 6GM8 with another suitable tube... Any thoughts on this?

11th May 2012, 03:56 PM	#7
kingfisher diyAudio Member Join Date: Feb 2010 Location: Eastern Ontario CA.	Most of my problem stems from getting the purchase completed! I know this is a odd question, but how did you go about buying the board?

11th May 2012, 09:59 PM	#8
wirewiggler diyAudio Member Join Date: Mar 2005 Location: Bakersfield Ca	Are you on the glassware site? GlassWare Audio Design Software Bill