Help making a circuit - diyAudio
Go Back   Home > Forums > Source & Line > Analog Line Level
Home Forums Rules Articles diyAudio Store Gallery Wiki Blogs Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Analog Line Level Preamplifiers , Passive Pre-amps, Crossovers, etc.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 16th January 2011, 03:45 AM   #1
diyAudio Member
Join Date: Jan 2011
Default Help making a circuit

I'm quite a noob, and trying to finish my project.
Basically, I'm splicing in my zune to my cars factory radio.
I did this by cutting the L&R audio (out) from the AM/FM turner, and hooked my Zune to it. (pre-amplifier)
Problem is, if the Zune's volume is up too loud, it sounds like crap. I havent turned it up all the way, as I'm afraid I'm going to blow something up.

Im trying to find/build/design a circuit that will regulate the audio level before if enters the amp.

The simpler the better, and with any luck, it'll operate on 12ish volts

Any ideas?
  Reply With Quote
Old 16th January 2011, 12:17 PM   #2
AndrewT is online now AndrewT  Scotland
diyAudio Member
Join Date: Jul 2004
Location: Scottish Borders
a potentiometer (variable resistor) is normally used to control/adjust output voltage.

A two gang 20K log law potentiometer can be bought from a few 10s of cents to hundreds of $.
Start cheap and find out how to control volume.
regards Andrew T.
Sent from my desktop computer using a keyboard
  Reply With Quote
Old 17th January 2011, 07:42 AM   #3
Join Date: Nov 2006
Location: Torpoint
Yes you will certainly BLOW SOMETHING UP.

The output of your existing stereo will be sufficiently high to cause the "Zune" to CLIP. This can be destructive to most amplifiers and most speakers.

If you read up about potential dividers you will see what AndrewT is getting at.

A "poor" car stereo may only output 4Watts RMS. Better stereos may output more than this.

Assuming 4W RMS we are looking at about 4V RMS at the speaker terminals of the stereo. The "Line - In" of the ZUNE may be adjustable but it is normal for Line - In to be between 0.1 and 1V RMS.


If your existing stereo already has a bridged output, normally detected by neither speaker being grounded, then you may not be able to use the above approach as you will effectively short circuitthe output of the existing stereo.

The input impedance of the ZUNE may be in the order of 10 K Ohms (again this depends on the amplifier).

As a general rule of thumb, let us keep the potential divider at 1/10th of this figure to prevent loading. So the two resistors of the potential divider need to total about 1 K Ohm.

If we've got 4V RMS in and want 1V RMS out then using a 3K in series with a 1K will give you the required output across the 1K.

As everyone knows, 3K is not a standard value so we can use the closest standard value. 3K3 or 2K7 wont make much difference.

Alternatively you could use a 4K7 potentiometer and adjust the wiper to give the same result.

If the input sensitivity or input impedance of the ZUNE is significantly different then you may need to experiment a bit.

Last edited by Andy5112405; 17th January 2011 at 07:45 AM.
  Reply With Quote
Old 23rd January 2011, 03:21 PM   #4
diyAudio Member
Join Date: Dec 2010
Location: wigan
How about setting the zune volume control till it just starts to distort then reduce setting a little. Then use the volume control on the car stereo.
Regards Mad Mark
Ps andy a zune is a personal digital audio file player.
From what i gather he has been inside the stereo and connected the zune to where the tuner used to connect as he neede that input for is zune .
Best Regards Mad Mark
  Reply With Quote


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
Making a Woofer jwatts Multi-Way 33 2nd March 2009 06:27 PM
Making a two way Zardoz89 Multi-Way 6 23rd February 2009 12:40 AM
Making you're own pcb's jazz Everything Else 1 20th November 2008 05:36 PM
The Making of a Triode emilesprenger Tubes / Valves 8 21st December 2006 11:49 AM
Trouble with speaker protection circuit (Randy Slone's circuit) whalefat Solid State 3 13th April 2005 10:13 AM

New To Site? Need Help?

All times are GMT. The time now is 08:29 AM.

vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999-2017 diyAudio

Content Relevant URLs by vBSEO 3.3.2