Yet another Volume controlers and source selections

[TBKK]

danzup,

nice job, i want to build the one with LED.
I see only the sources for the LCD not for the LED
or can I use the same BAS files for both.

How do you indicatie the input source on the LED?
does it work in every RC5 remote control?
I have an tube preamplifier with a potentiometer of 22k, can I use this design?
I take 60 sec. to warm up the tubes is it possible to change that?
I prefer the Matrix displays is this also possible?

[danzup]

Originally Posted by TBKK

danzup,

nice job, i want to build the one with LED.
I see only the sources for the LCD not for the LED
or can I use the same BAS files for both.

How do you indicatie the input source on the LED?
does it work in every RC5 remote control?
I have an tube preamplifier with a potentiometer of 22k, can I use this design?
I take 60 sec. to warm up the tubes is it possible to change that?
I prefer the Matrix displays is this also possible?

Here are the bin and hex for LED . The .bas files are not in archive .
You must try the ir remote to find the one that work with controller .
When you press the menu button the LED display flash and display from 1 to 4 input then after 30 secs flash again and change automatically to display volume again .
Firmware for tube is different that that for SS so this firmware must be used only for tube variant.
I do not have a matrix variant .

[TBKK]

danzup,

can you explane what happen on the display does it count 60 sec back or what?
the remote control voor LCD is easier according to the post is it difficult to build this also for the LED? I have two remote control of Philips that mean i must have more?

because LED is very simple how can you see witch input you have select?

[danzup]

Originally Posted by danzup

Here are the bin and hex for LED . The .bas files are not in archive .
You must try the ir remote to find the one that work with controller .
When you press the menu button the LED display flash and display from 1 to 4 the input selected then after 30 secs flash again and change automatically to display volume again .
Firmware for tube is different that that for SS so this firmware must be used only for tube variant.
I do not have a matrix variant .

Yes it is counting from 70 sec down after power on to wait for tube to heating .

[didiet78]

For remote control, i build based on App Notes #105 from MCS Electronics AN #105 - Sending RC5 and SONY IR codes - MCS Electronics,
with just change RC5 System Address and RC5 Command.

[danzup]

Originally Posted by didiet78

For remote control, i build based on App Notes #105 from MCS Electronics AN #105 - Sending RC5 and SONY IR codes - MCS Electronics,
with just change RC5 System Address and RC5 Command.

Perfect done !
Also , I have used that piece of software for Sony IR codes and work perfectly.
For those who want to use Sony instead RC5 /Philips .

[didiet78]

This my remote full view

And this component view no smd

[Jempie]

Hi Danzup,

Thanks for all, work perfect, do you have the volume Bar for the PGA2310 software

Thanks
Jempie

[danzup]

Originally Posted by Jempie

Hi Danzup,

Thanks for all, work perfect, do you have the volume Bar for the PGA2310 software

Thanks
Jempie

Hi Jempie , no .
I do not have such firmware.
If I will have some time in future I will write .
Best regards.
Dan

[Pryanick]

Hi
Here is my bar graph version

Dim I As Word
Dim Cols As Word
Deflcdchar 0 , 32 , 32 , 32 , 27 , 27 , 32 , 32 , 32 ' empty symbol
Deflcdchar 1 , 32 , 32 , 31 , 31 , 31 , 31 , 32 , 32 ' filled symbol
Declare Sub Bargraph
...
...
...
'-----Bar graph------
Sub Bargraph:
Cols = L / 17
Locate 1 , 1
For I = 1 To Cols
Lcd Chr(1)
Next I
For I = Cols To 14
Lcd Chr(0)
Next I
End Sub