Hi,
Thank you for the feedback
About the VU-Meter version I dont think anyone use it yet
I never seen any feedback on this version
Last edited:
RC5 Tester
For long time Read here all Thread about RC5 and do experiment to Learnig,
but I Flash your RC5 Tester and to start programm coming only ( RC5 Remote Read) and Display go out, I have with 3 Remote controller (Sony,Terratec and Sharp) and Do nothing, I only do other LCD configuration,
Config Lcdpin = Pin , Db4 = Portc.4 , Db5 = Portc.5 , Db6 = Portc.6 , Db7 = Portc.7 , E = Portc.2 , Rs = Portc.3
and PortD.3 ist the output from my SFH5110 and chance to experiment with TSOP 1738 and no go, please can you say why? I have all in my STK500.
Thank
stk500
Hi Kim!Hi,
Here is a code for RC5 debug
It show:
Address info + code
Command info + code
Easy to reprogram a multi ir remote when you can see the address/command on LCD
An externally hosted image should be here but it was not working when we last tested it.
I used my ATM16 but eny other AVR can be used
run INTRC 8Mhz Disable JTAG if your chip have it
LCD 16*2
/Kim
@ Edit input text works now auto fill space on save via RC5 allmost finish code
For long time Read here all Thread about RC5 and do experiment to Learnig,
but I Flash your RC5 Tester and to start programm coming only ( RC5 Remote Read) and Display go out, I have with 3 Remote controller (Sony,Terratec and Sharp) and Do nothing, I only do other LCD configuration,
Config Lcdpin = Pin , Db4 = Portc.4 , Db5 = Portc.5 , Db6 = Portc.6 , Db7 = Portc.7 , E = Portc.2 , Rs = Portc.3
and PortD.3 ist the output from my SFH5110 and chance to experiment with TSOP 1738 and no go, please can you say why? I have all in my STK500.
Thank
stk500
Hi STK500
If te Lcd show "RC5 Remote Read" then you lcd is setup OK
This code only works with Philips RC-5 Protocol
Sony , Sharp, RCA ect do not work with this code
did you program it as INT 8Mhz CLKDIV/8 = off else it runs 1 Mhz
how did you connect the IR ? pullup 10K ?
If you look at Bascom Hep serach for "GETRC5"
you can learn more about the IR part
Here is Sam Bergmans web lots of good info about Remote IR Protocol
If te Lcd show "RC5 Remote Read" then you lcd is setup OK
This code only works with Philips RC-5 Protocol
Sony , Sharp, RCA ect do not work with this code
did you program it as INT 8Mhz CLKDIV/8 = off else it runs 1 Mhz
how did you connect the IR ? pullup 10K ?
If you look at Bascom Hep serach for "GETRC5"
you can learn more about the IR part
Here is Sam Bergmans web lots of good info about Remote IR Protocol
Last edited:
If you don't mind...I will try it
I make a update later today for EQ
Hi Kim!
Thank you for you Info, Well I think one RC for (Sony,Terratec and Sharf) maybe work, I see the signal in my Oscillocope in the output of IR, but maybe you know Who find one Send RC5(Philips protocoll) to tester Software and Hardware?
My plan ist to control Led with music for my living hall with RGBW led, when in finish my project coming here in forum, open source. but with you name in the Source Programm.
bye
hasta la vista amigo!
stk500
Thank you for you Info, Well I think one RC for (Sony,Terratec and Sharf) maybe work, I see the signal in my Oscillocope in the output of IR, but maybe you know Who find one Send RC5(Philips protocoll) to tester Software and Hardware?
My plan ist to control Led with music for my living hall with RGBW led, when in finish my project coming here in forum, open source. but with you name in the Source Programm.
bye
hasta la vista amigo!
stk500
Why my name I did not write your program
If you like to make it in bascom then come to Http://bascom-forum.de
this is the German bascom forum lots of good code and help
See sample in bascom\samples\ir folder
About RC5 RGB see this link (German) http://www.ledstyles.de/ftopic1760.html
Last edited:
Hi
No its for Projetc nr.3 see post #4
and Post #348 VU-meter addon
but to get the full storry you have to read the hole Thread lots of addon is made for Danzups controller 1.6C
start at post #3 and read
Last edited:
Hi
No its for Projetc nr.3 see post #4
and Post #348 VU-meter addon
but to get the full storry you have to read the hole Thread lots of addon is made for Danzups controller 1.6C
start at post #3 and read
I understand you!
Thank you very much for your attention
Be a problem for you, "tie"to your firmware management for PGA?
Hi,
A the moment Iam making a motorpot version
but have no plans for making a PGA2311 version
If you read the posts you will find code for a PGA2310 version
and you can edit the software for M16
I just completed building the latest Rev 2.1.b.
After I apply power, the LED reads "10", and I can adjust the volume up or down. So it seems to work. I am using the R2R settings.
My problem is: After about 5 sec, one of the relays clicks, and the LED goes off.
If I recycle power, it does the same thing again.
Has anyone experienced this, or know what might be the problem?
Thanks,
Dave
After I apply power, the LED reads "10", and I can adjust the volume up or down. So it seems to work. I am using the R2R settings.
My problem is: After about 5 sec, one of the relays clicks, and the LED goes off.
If I recycle power, it does the same thing again.
Has anyone experienced this, or know what might be the problem?
Thanks,
Dave
Hi,
Ok and when you program chip
you remember to disable Jtag
and setup clock to 8Mhz int ?
Link LCD Atmel software ATM16_SHUNT_R_2R_LCD_V1.zip Vicol Audio
Ok and when you program chip
you remember to disable Jtag
and setup clock to 8Mhz int ?
Link LCD Atmel software ATM16_SHUNT_R_2R_LCD_V1.zip Vicol Audio
Last edited: