Aspen Headphone Amp - Page 100 - diyAudio
Go Back   Home > Forums > Commercial Sector > Manufacturers > AKSA

AKSA Builders of market proven kits and modules at sound quality to rival the best in high end

Reply
 
Thread Tools Search this Thread
Old 19th November 2009, 02:30 AM   #991
Account disabled at member's request
 
MJL21193's Avatar
 
Join Date: Mar 2007
My mantra is to "prevent clipping at all cost". That shouldn't be a problem in a headphone amp.
  Reply With Quote
Old 19th November 2009, 11:15 AM   #992
p-w is offline p-w
diyAudio Member
 
Join Date: Oct 2009
Hugh - thanks for explaining about the distortion to me, it is interesting how sensitive the ear is to such low levels of the odd harmonics. Also I had not realised why such high speed was beneficial to the reproduction of audio frequencies before.

Kean - thanks for the encouragement

I have been thinking about the simulations and the simulated distortion levels in particular. If we are only interested in currents and voltages then a simulation with an accuracy of tree or four significant figures will be fine for the vast majority of situations. However, if we want to accurately calculate the amplitude of high order distortions which are at -140dB relative to the fundamental we need an accuracy of eight significant figures in the transient simulation from which the harmonics are calculated. It matters whether a voltage is 1.0000000 or 1.0000001. This puts much higher constraints on the accuracy of the simulation. The underlying physical device models need to be very good to give this level of correlation with reality, the model parameters we use need to be very accurate and the simulator needs to take care of numerical effects arising from the computation. I don't really have a feel for how accurate the models used by the simulators are and with this in mind I was wondering what the likely uncertainty is on the simulated values of the harmonics?

Best wishes

Phil
  Reply With Quote
Old 19th November 2009, 11:32 AM   #993
diyAudio Member
 
Join Date: Nov 2009
Hi Mj.
Just read your post regarding clipping problem faced by you for designing
a circuit design for your headphone. Clipping do reduce the noise effect,
so its a matter of consideratiion to reduce it and keep it as low as possible.
Thanks for your post and stay connect.
  Reply With Quote
Old 19th November 2009, 11:43 AM   #994
Account disabled at member's request
 
MJL21193's Avatar
 
Join Date: Mar 2007
Quote:
Originally Posted by p-w View Post
...and with this in mind I was wondering what the likely uncertainty is on the simulated values of the harmonics?

Best wishes

Phil
That's one of the things I've seen - too much stock put into the simulated spectrum. It has been my experience that the raw THD figure (0.045% for example) is relatively accurate, but the spectrum has not been confirmed and it's accuracy I strongly doubt - it will change, sometimes radically, with a different device model (could be the same device, different manufacturer model).
At best I think it can give a "hint" as to what the spectrum may be if you manage to use accurate models and can get similar results with similarly accurate models on a second simulation run.
  Reply With Quote
Old 19th November 2009, 12:57 PM   #995
p-w is offline p-w
diyAudio Member
 
Join Date: Oct 2009
Hugh - Just realised I forgot to say anything about your great new circuit! Judging from your simulations the additional gain and negative feedback offer really good performance combined with simplicity - looks like you've been working hard for us again. I also wanted to say that my question about the simulations was asked out of a general interest in trying to better understand things, it is not meant to be a criticism of your simulations in anyway.

John - thinking about it the fact that you see the raw THD figure being more accurate makes sense as it will be dominated by the larger amplitude harmonics which are easier for the simulator to get right. Also being a sum some errors on the individual harmonic components may well cancel out.

Phil
  Reply With Quote
Old 19th November 2009, 01:26 PM   #996
Account disabled at member's request
 
MJL21193's Avatar
 
Join Date: Mar 2007
Here's an example. I used the same circuit but changed one device, in this case the output in Hugh's circuit. I used the MJE350 that was in the Multisim library (I'm not sure where it originated) and I used the MJE350 model from Fairchild.
The MS model:

117.PNG

The Fairchild model:

118.PNG

Quite a difference, even in the raw THD number when there really shouldn't be - same circuit, same condition, radically different results.

With that said, Hugh's circuit is a good one for testing the consistency of these models and I believe the harmonic spectrum is fairly accurate, as I have been randomly "plugging in" various known good models and getting nearly the same result. It should be a very good sounding amp.

(pleasant John today )
  Reply With Quote
Old 19th November 2009, 04:59 PM   #997
tent is offline tent  Germany
diyAudio Member
 
Join Date: May 2009
Hi all,
your project seems really great! Btw I just got lost in reading the hundert of posts you already did in this thread..
Maybe somebody could make me some sort of "current status of the project"?
Would help me understand which are the latest schematics/ideas for PSU, crossfeed, HeadAMP and POT you are currently holding.....
And another thing: are you now planning to go with batteries or did I miss something? =D

Thanks!
tent:wq
  Reply With Quote
Old 19th November 2009, 08:16 PM   #998
AKSA is offline AKSA  Australia
diyAudio Member
 
Join Date: Sep 2001
Location: Melbourne, Australia
Phil,

A glance at the models used in LTSpice reveals all parameters are at 6 significant figures. For example, here is the MJE15031 taken from the library with Notepad:

.MODEL MJE15031 pnp IS=7.17489e-11 BF=457.169 NF=1.11376 VAF=6.01557 IKF=0.345808 ISE=1e-08 NE=2.18567 BR=0.247882 NR=1.39549 VAR=60.1557 IKR=0.0263893 ISC=1e-16 NC=2.89486 RB=2.29208 IRB=0.0114006 RBM=0.000102795 RE=0.00815557 RC=0.0407779 XTB=0.1 XTI=0.1 EG=1.05 CJE=1.64037e-09 VJE=0.819491 MJE=0.537987 TF=1.60991e-09 XTF=180.82 VTF=1.16561 ITF=6.50499 CJC=4.82516e-10 VJC=0.4 MJC=0.374287 XCJC=0.786653 FC=0.712788 CJS=0 VJS=0.75 MJS=0.5 TR=3.32795e-08 PTF=0 KF=0 AF=1

What is in doubt is the veracity of these models. I am not skilled in this area, but I'm told there are some glaring inadequacies, for example the Early effect is not prescribed, and behaviour of beta at very low Vce is not accounted for. The expert in this area, a mathematician, is Andy_C, also on this forum. Neither is the Berkeley spice engine transparent; we cannot know if all aspects of transistor operation are incorporated in the computation of THD.

However, my thoughts are that the basic device parameters are accurate and this is useful for back of the envelope scratching during the early stages of design. It enables viability of a topology to be quickly tested and operating points refined. Assuming the distortion artefacts are fully accurate is probably foolish, but in the absence of an AP it's better than nothing, and certainly tells you quite a bit about distortion profile; whether artefacts are same magnitude, or monotonically decreasing, for example. (One might even ruefully consider the stunning correlation, or lack of it, between THD and sound quality, but that is a separate issue!) Since these are essentially command line programs, there is a learning curve not unlike Unix, and some will have very sophisticated analysis techniques, which can lead to a variety of answers, trending simulation towards interpretation rather than unarguable, objective fact. I have also seen quite different results between LTSpice and MicroCap, for example, an outstanding, commercial program used here by Nico, and this would indicate that for thoroughness one should always examine circuits in detail with two different programs, one preferably fully commercial, and therefore very costly. You need the proper tools; you don't go to war in a Fiat Uno.

The real issue is stability. The Bode plot looks pretty good on LTSpice, but figuring the very low value stability capacitors is best done empirically, particularly as it so affects sound quality.

If I spent as much time building amplifiers as I do on this board, I would have completed the project by now. I'm trying to build group participation, but it's very time intensive.

Phil, Earle Geddes, a very smart investigator of distortion measurements and sound quality correlations, has postulated a new metric, the Gedlee parameter, which attaches sharply increasing weighting to higher order, particularly odd, harmonics. This is said to correlate far better with sound quality, and might be worth investigating. I have never been happy about the simple observation that a much vaunted single ended triode amp with 2% THD sounds somehow more pleasing than a 0.01% SS amplifier. This is absurd, and makes a mockery of THD measurement. OTOH, I have always been impressed with Jean Hiraga (Japanese French audiophile from the sixties who developed 'Le Monstre', a legendary amp of only average THD but wonderful sound) and John Linsley Hood, an English nuclear scientist who died recently at 78 and who designed a 10W Class A amp in 1969 (and again in 1996) with lousy measurements but wonderful sound.

John, thank you for your tireless input. You are indeed in good humor today!

Tent, stay posted, main circuit block coming!

Cheers,

Hugh
__________________
Aspen Amplifiers P/L (Australia)
www.aksaonline.com
  Reply With Quote
Old 20th November 2009, 12:23 AM   #999
diyAudio Member
 
keantoken's Avatar
 
Join Date: Aug 2006
Location: Texas
Blog Entries: 2
Hmmm, I feel like I could develop BJT models on commission....



Oh yes... For those who haven't noticed... LTSpice wiki section!

LTSpice and What the New User Should Know - diyAudio

- keantoken
  Reply With Quote
Old 21st November 2009, 08:10 AM   #1000
diyAudio Member
 
Nico Ras's Avatar
 
Join Date: Nov 2005
Location: East Coast of South Africa
Models from different manufacturers are different, an MJE350 from one manufacturer is not identical to another manufacturer. On Semi is good if you use On semi transistors. Fairchild is good if you use Fairchild transistors. I am stumped when someone develops a model for an MJE350 transistor, which one did they use, how the heck did they make some of the measurements, very sophisticated equipment is required that exists at a semiconductor design plant?

Using a professional simulator with purchased models you get it by manufacturer, not by part name only. Furthermore you should run Monte Carlo to accommodate for the spread of specs of the same components, temperature spread, supply spread and so on. We all know that almost all compo nets characteristics change with temperature, so what temperature is used in these simulations?

Besides semi-conductors you should use models for every component such as capacitors, resistors, op-amps since these contribute considerably to the end result.

A full simulation of a simple amplifier like this runs for more than an hour before reasonable results are available. Changing a component in the circuit could run another hour.

Nothing in life is free, if it is, it is not worth having. You can improve the simulations by running it and changing every component's model data by the best and worse case scenario, but this will take several days, considering the number of iterations that does exist.

Cheap or free programs are just that, if it was worth anything it would not be cheap nor free.

Good luck keantoken and others that say they compiled better models, I would really like to know exactly how would one do that without the equipment to measure it accurately. It would be a enormous task and very nice gesture if you would just start with all the variants of a 100uF capacitor from a few well common manufacturers and provide proper models for it.

If these things were all available, accounted for and used by the free simulators out there then I suggest that they would not be free by a long shot. I feel the same way regarding test and measurement equipment using a PC sound card. PC sound cards would put the likes of Hewlett Packard, Anritsu, Tektronix, Rhode & Swarch, Wiatzu, to name a few completely out of business. I hardly see that happening in industry, but it appears that the PC and free programmes are the audio designers epitome.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Another DAC + Headphone amp ghetto Digital Source 14 10th July 2008 04:02 PM
ESL Headphone X-former bjackson Planars & Exotics 5 19th September 2005 03:45 AM
Headphone amp audioPT Headphone Systems 5 28th September 2004 08:03 PM
Zen v4 headphone amp Rob M Headphone Systems 11 21st May 2003 12:58 AM
Aspen Amplifiers - the ASKA 100 WATT griff Solid State 25 13th April 2002 03:15 PM


New To Site? Need Help?

All times are GMT. The time now is 04:21 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2